Ozzyjuice; Proper Use And Care - SmartWasher SW-45 Manual De Operación

OzzyJuice

Solution
The SmartWasher uses a specially formu-
lated fluid which provides a combination of
excellent cleaning characteristics, safety
and nutrition for the Ozzy microbes.
OzzyJuice is provided in ready-to-use con-
tainers.
DO NOT ADD WATER, SOLVENT, MINERAL
SPIRITS, GASOLINE OR KEROSENE TO
YOUR SMARTWASHER!
To help monitor and maintain the proper fluid level, the
SmartWasher is equipped with a low fluid level indicator. When
the "Add Fluid" lights comes on, add a 5 gallon box of
OzzyJuice immediately. When a container of OzzyJuice is
added, the light will go out. When the "Add Fluid" lights
comes on, the heater will turn off until the necessary
amount of fluid is added.
Remember, the OzzyMat needs to be replaced every 30 days.
To Add OzzyJuice
Slowly pour a full container of
OzzyJuice directly into the
SmartWasher sink. The "Add Fluid"
lights should go out.
If you add a container of OzzyJuice to
your machine and the "Add Fluid"
lights are still on, lift up on the sink
and check to see if the float is in the
down position. If the fluid is below the
float and the float is not at the top stop,
you will need to add more fluid. If the
fluid is over the float, there may be a
problem with the low fluid indicator and
you should call your service representa-
tive.
2
Add Fluid Light
ChemFree Technical Support 1-800-521-7182 x2624
www.ChemFree.com
Temperature
Your SmartWasher should be plugged in 24 hours a day, 7 days
a week to maintain optimal temperature.
The thermostat is factory-set to maintain fluid temperature at
108° F(+-2°) (42°C)(+-1°). This temperature provides the opti-
mum condition for effective cleaning and activity of Ozzy
microbes.
The heater will not operate when the fluid level becomes critical-
ly low. Lift the sink and check your fluid level. Your
SmartWasher should have approximately 8 inches (20 cm.) of
fluid in it. If the fluid lever is lower than that, add OzzyJuice. If,
after a reasonable warm-up period, the fluid temperature seems
too hot or too cold, please refer to the "Troubleshooting" section
on page 3.
If the temperature falls below the recommended minimum, the
system will still clean, but remediation of the hydrocarbons by
the Ozzy microbe colony will slow down. However, the
microbes will not die. The Ozzy colony will become more
active when the fluid temperature reaches the appropriate
level.
PROPER USE AND CARE OF THE
SMARTWASHER
To keep your new system operating at its best, please remem-
ber these important tips:
• The heater is disabled as long as the "Add Fluid" lights are on.
• The SmartWasher is designed to "eat" the oil and grease
washed from dirty parts. It is NOT designed to function as
a waste-oil dump! The Ozzy microbes will thrive on oil and
grease washed from parts during normal use. If excessive
oil, gasoline, transmission fluid, antifreeze or similar fluid is
dumped into the system, the Ozzy microbes may be
destroyed.
• DO NOT ADD - water, bleach, disinfectants, insecticides
or biocides of any description.
• Change the OzzyMat every month.
• To maintain the effectiveness of the SmartWasher, it is
imperative that nothing be added to OzzyJuice other than
replacement OzzyJuice, or dirty parts residue.
• Turn off pump when not actually washing parts. This will
help to decrease fluid evaporation.
• Do not clean paint brushes in the SmartWasher; Ozzy
Microbes will not consume the inorganic pigments in paint.