Displ Y Indic Tions - Fagor STT 8000 Manual Del Usario

I
DESCRIPTION
DVB-S and DVB-S2 signal transmodulator in DVB-T
G
Free-to- ir (STT 8000) and with Conditionnal ccess
DVB-CI (STT-CI 8000). dmits QPSK or 8PSK input
signals and modulated signal delivery in COFDM.
llows satellite programs to be viewed with DTT receivers.
1st IF S T signal with digital programming is converted
to the RF band between 50.5 and 858 MHz modulated
in DVB-T. Handles MPEG-2 or MPEG-4 signals enabling
selection of programs delivered on output.
I
INST LL TION ND ST RT-UP
- The power sources must be disconnected from
the mains before connecting or disconnecting the
module.
Insert the C M into the module ( look position N 10
G
in the CONTROLS schema) before placing the module
on the frame (STT-CI 8000).
Connect the earth connection of the frame to the earth
G
connection of the antenna installation.
Fix the modules to the frame in the order shown in the
G
application example (see Fig.2), with the power source
on the right and the amplifier on the left of the unit.
Make the signal distribution of the antenna(s) via the F-F
G
coaxial bridge (Ref. 83814) and load the free output(s)
with 75 (Ref. 84011).
Join the RF channel outputs (Fig.1, 8) via the F-F coaxial
G
bridge, and load the free output of module 1 with 75 ,
beside the power source.
Connect the Supply bus B 807 ref. 83807 between the
G
modules (Fig.1, 5) and the SPS.
Connect the antenna drop cables to the corresponding
G
inputs (Fig.1, 1).
Connect the power source to the mains.
G
I
WORKING TEMPER TURE
The modules have to be refreshed for their correct
G
operationt. It's recommended to install the modules in
the housing with fan (Ref 83806) or, when installing on
a 19" rack, to use the Rack ventilation Unit (ref 83801)
When there are few modules to install, it's possible to
use the fan VNT 800 on the wall frame (Fig.1, 5).
I
MODULES PROGR MM TION
The modules can be programmed:
Through the UCF 300 Control Unit (Ref 85115) in local
G
mode, following the steps explained in this manual.
Through a PC in local mode. In this case, it's necessary
G
to have a MCU 8000 unit and the "8000 series" interface
installed in the PC.
I
UCF 300: BUTTONS' FUNCTIONS
J J
The buttons are for vertical menu scrolling.
L
M
G
a) On the programming menu they are for selecting the
function to be programmed.
b) parameter can be selected within a function.
c) parameter setting can be modified within a
programmable parameter.
The buttons are for horizontal scrolling through the
G
programming menu, e.g.:
Function parameter
The button is for moving right.
G
The button is for exiting without changing the setting:
G
escape.
The button is for validating the data item programmed.
OK
G
I

DISPL Y INDIC TIONS

The UCF 300 control unit has two rows of alphanumerical
G
characters. The data display mode and programming
diagram on page 8 are a guide to this process:
If the characters are all upper case and on the upper
G
row, this indicates that one of the 5 functions has been
entered.
If data appear on two rows of the display, the
G
parameter to be adjusted is being displayed.
The right arrow shows how to enter to change the
G
parameter setting.
flashing box indicates that the parameter setting can
G
be modified using the
(press the button to validate).
OK
"+" sign followed by the name of the service indicates
G
that this service is in the output multiplex.
" * " sign before the name indicates an encrypted
G
service.
I
PROGR MMING with UCF 300
Connect the UCF 300 to the desired module. fter a
G
few seconds, the unit will show the model in question:
STT 8000.
Press the button to enter the standard menu
G
(press 3 sec to go to the extended menu):
OK
1. RF OUTPUT
2. DVB-T OUTPUT (extended menu)
3. LNB (extended menu)
4. S T INPUT
5. OUTPUT SERVICES
6. PSI EDIT (extended menu)
7. C M (extended menu) / (STT-CI 8000)
8. MEMORY
J J
Press the button to scroll through the functions.
L M
G
Press the button to enter the parameters of the
G
desired function.
See programming diagram on page 8.
1. RF OUTPUT: RF output
1.1. Out Frequency:
1.2. Out Level:
65 ÷ 80 dBµV
1.3. Out RF:
Enables/disables the RF output.
14
value.
J J
L
M
50,5 ÷ 858 MHz.
.