Fagor STT 8000 Manual Del Usario página 15

2. DVB-T OUTPUT: DVB-T output
2.1. DVB T Mode:
2K, 8K.
2.2. Q M Mode:
QPSK, 16 Q M, 64 Q M.
2.3. Code Rate:
FEC 1/2, 2/3, 3/4, 5/6, 7/8.
2.4. Guard Interval:
1/4, 1/8, 1/16, 1/32.
2.5. Bandwidth:
6, 7, 8 MHz.
2.6. IQ mode:
normal, Inverted.
3. LNB: LNB supply voltage and configuration
3.1. LNB Polarity:
0V, +13V, +18V, +13V 22KHz, +18V 22KHz.
3.2. DiSEqC Satellite:
OFF, S T , S T B, S T C, S T D.
3.3. DiSEqC Polarity:
OFF, V Low, H Low, V High,
V High.
4. S T INPUT: Satellite input signal
4.1. DVB Mode:
DVB-S, DVB-S2.
4.2. In Frequency:
FI S T 950 ÷ 2150 MHz.
4.3. Baud Rate:
4.000 ÷ 45.000 KB, DVB S
10.000 ÷ 30.000 KB, DVB S2.
4.4. Roll Off:
20, 25 y 35%, DVB S2 only.
4.5. Init Tuner:
Syncronize the tuner (press
4.6. * Modulation:
indicates the modulation type.
4.7. * BER:
indicates the value of BER.
4.8. * S/N:
indicates the input S/N
(Recommended S / N > 11 dB).
* This data is shown when the tuner is tuned.
5. OUTPUT SERVICES
- This function is only visible when the tuner is tuned.
5.1. List of Services:
list of services.
Press to view the list.
G
J J
Press to select the service.
L
M
G
Press to enter the service parameters.
G
– "+" sign followed by the name of the service indicates
that this service is in the output multiplex.
– " * " sign before the name indicates an encrypted
service.
5.1.1. ctive:
enables the service on output MUX
J J
(use to select and press
L
M
5.1.2. LCN:
llows assigning a LCN (Logical Channel Number)
between 1 and 999 to the services at the output
J J
(select with and press
L
M
NO LCN).
5.1.3. Program Number:
indicates the service PN.
5.1.4. Program Nb Edit:
Permits to change the value of the
PN associated with a service between 1 and 65535.
Changing from its initial value should be different for each
J J
service (select with
L M
5.2. Output MUX BW:
indicates the total % of the output
MUX occupied.
- It is not recommendable to work with the output MUX BW
above 92%, as the services may increase their bitrate during
transmission. (Output MUX BW > 92%: Status LED in yellow).
).
OK
.
).
OK
; 0000 stands for
OK
and press ).
OK
5.3. Clear all:
clears all the services selected in the DVB-T
output. "Press ".
OK
5.4. Read Services:
reads the transponder services.
"Press ".
OK
6. PSI EDIT:
llows the Output's NIT configuration.
6.1. NIT Mode:
Pass-Through / LOC L selection. If local is
chosen, allows modifying the following parameters.
6.2. Network Name:
llows living a name to the network.
6.3. Network ID:
(give the same value as the Orig.Net.ID).
6.4. TS ID:
Some receivers need a different TS ID for every
memorised module (value between 0 and 65535).
6.5. Orig. Net. ID:
Original Network Identifier by Country
(see table 3).
6.6. Vr. NIT:
NIT version table.
6.7. Vr. SDT:
SDT version table.
6.8. LCN Mode:
Generic/UK. llows to generate the NIT
according to different standards.
7. C M: access to MMI and C M menus
(STT-CI 8000)
7.1. Read MMI:
Open the session with the MMI
(only option available if session is not open).
If the session is open, the last option is read again.
7.2. Close MMI:
Closes the session with the MMI.
It's recommended to close the MMI session once
finished the access.
7.3. MMI menu:
Options list or C M information.
It can appear a first information line followed by the list
of options with a number. The last option (0.Quit) goes
to the precedent menu. If the information to show
is longer than the display size, push
of the text.
7.4. MMI Enquiry:
C M's data introduction (example
insert PIN). Look at point 6.5.
7.5. Enter User Input:
C M's data introduction.
8. MEMORY
- utomatic save: 30 minutes after the last button
is pressed, the current data will be stored in the
STT 8000.
8.1. Save Configuration:
8.2. Restore Configuration:
stored in the unit to be recovered.
8.3. Save Configuration, Device to UCF 300:
enables the configuration stored to be saved with an
identifying name in one of the 26 memories of the
UCF 300.
8.4. Load Configuration, UCF 300 to Device:
ecovers the data in one of the UCF 300's memories
with data recorded from an STT for cloning on another
STT 8000.
15
to read the rest
Stores current programming.
Enables the configuration