Options And Maintenance - Ecco 10 Serie Instrucciones De Operación

Ocultar thumbs Ver también para 10 Serie:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Options and Maintenance:

Occasional cleaning of the lenses will ensure optimum light output. Take care when cleaning lenses – although tough, polycarbonate
scratches easily. Clean the lens and base with soap and water or a lens polish using a soft cloth. Do not use solvents as they may damage
the polycarbonate. Do not subject the light bar to high-pressure washers or automatic car washers.
Lens Removal and Installation
10/15 Series
1. Remove retaining screws from both ends of the lightbar. Using a small flat blade screwdriver or similar tool, lever open the latches
around the lightbar.
2. Carefully lift the lens off the seal – choose a suitable location to temporarily store the lens so as to not scratch the surface.
3. Ensure latches are captive in the lower lens before refitting the upper lens.
4. When reinstalling, gently apply pressure around the upper lens taking care not to damage the seal around the lower lens set. Push all
latches back on the lens. Replace the retaining screws.
20/30 Series
1. Remove four retaining screws from the end lenses taking care not to lose the o-rings (30 Series only). Using a small flat blade
screwdriver or similar tool, lever open the latches around the lightbar.
2. 20 and 30 Series Lightbars are generally fitted with hinges at the front of the bar - if the lightbar does not have a hinge refer to step 2 in
10/15 Series lens removal. From the back of the lightbar gently lift the upper lens until it clears the seal, continue lifting the lens over the
front of the bar until it rests on the hinge backstop.
3. Ensure latches are captive in the lower lens before refitting the upper lens.
4. When reinstalling, gently apply pressure around the upper lens taking care not to damage the seal around the lower lens set. Push or
lever all latches back on the lens. Replace the retaining screws and o-rings as required.
Rotators
Rotating light sources are used as a primary warning system. Rotators may be installed in
the upper level of both the 20 and 30 Series Lightbars, and are diagonally staggered to
optimize light output through the ends of the lightbar. Rotators are available to suit either H1
or S795 (Bayonet) type bulbs, in 12V or 24V and 90 rpm or 150 rpm – these specifications
are not configurable by the user.
Rotators are installed using 4 M4x16mm screws through rubber isolating feet.
Do not oil or grease rotators – they are constructed with self-lubricating material.
!
WARNING!
Halogen bulbs are extremely hot! Allow to cool completely before attempting to remove. Gloves and eye protection should be
worn when handling halogen lamps as they are pressurized and accidental breakage can result in flying glass.
Consider changing all of a specific bulb type when one burns out. This will minimize removal and replacement of outer lenses.
H1 Bulb:
1. See "Lens Removal" for instructions on removing and replacing lenses.
2. With the rotator reflector facing the motor, undo the retaining clip.
3. Lift the globe out to reveal the spade receptacle. Slide the bulb and its holder toward the motor.
4. Grip both the bulb and receptacle and pull apart. Do not stress the wire.
5. Replace with equivalent bulb. Do not touch the glass portion of the bulb – natural skin oils can cause
premature bulb failure.
6. Slide the bulb back into position and replace the clip.
7. Verify the rotator will spin.
8. Power up, and test the system before replacing lenses.
920-0052-00 Rev. F
Page 8 of 17

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

15 serie20 serie30 serie

Tabla de contenido