Fresado De Las Canales Del Escurridor - Virutex UC317S Manual De Instrucciones

a un desplazamiento de la varilla de ajuste fino Y de 1 mm, teniendo
un recorrido máximo de 5 mm. Cada división del indicador graduado
del ajuste fino A1 corresponde a un avance de 0.1 mm.
Una vez tenga el equipo preparado, sitúe la máquina en la posición de
inicio del fresado de la canal. Ponga en marcha la máquina y baje la
herramienta de corte hasta que la varilla haga tope en la torre giratoria
y a continuación bloquee la altura de la máquina con la palanca de
bloqueo V. Para tener absoluta seguridad, deberá bloquear la máquina
con la tuerca y contratuerca A3. Realice el fresado de la primera canal
del escurridor y vuelva a dejar la máquina en la posición de reposo.
Si lo considera necesario, disminuya el desnivel de la canal bajando la
altura del equipo de fresar canales.

5.8. FRESADO DE LAS CANALES DEL ESCURRIDOR

Según las dimensiones de anchura del fregadero, determine el número
y la distancia entre cada una de canales del escurridor, para que sean
apropiadas para el correcto desagüe en el fregadero.
Para realizar el fresado de todas las canales, libere la presión de la
ventosa de apriete K del equipo plantilla llevando la palanca central
a la posición vertical y seguidamente, afloje el pomo de fijación E
(Fig. 2). Sitúe el equipo en la posición de fresado de la segunda canal,
desplazando la guía a través del riel. Utilice como referencia de des-
plazamiento, el índice del visor N de la brida de fijación, sobre el regle
milimetrado (Fig. 1). Vuelva a bloquear firmemente el pomo de fijación
de la brida E y la ventosa de apriete K del equipo de fresar canales en
esta posición. Realice sucesivamente todas las canales del escurridor
mediante el mismo procedimiento.
6. UTILIZACIÓN DEL EQUIPO PARA CORTES
PARALELOS Y FIJACIÓN UF317S
Lea atentamente el manual de instrucciones del Equipo para cortes
paralelos y fijación UF317S/UFN317S, antes de usarlo para otras apli-
caciones (Fig. 10 y 11).
7. GARANTÍA
Todas las máquinas electroportátiles y accesorios VIRUTEX, tienen una
garantía válida de 12 meses a partir del día de su suministro, quedando
excluías todas las manipulaciones o daños ocasionados por manejos
inadecuados o por desgaste natural de la máquina.
Para cualquier reparación dirigirse al servicio oficial de asistencia
VIRUTEX S.A.
VIRUTEX se reserva el derecho de modificar sus productos sin previo
aviso.
UC317S DISH DRAINER ROUTING DEVICE
1. SAFETY INSTRUCTIONS FOR USING THE UC317S DISH
DRAINER CHANNEL ROUTING DEVICE
Read these OPERATING INSTRUCTIONS and the attached
GENERAL SAFETY INSTRUCTIONS LEAFLET carefully
before using the UC317S DISH DRAINER ROUTING
DEVICE. Make sure you have understood them before
operating the machine. Keep both sets of instructions
for future reference.
Also carefully read the Operating Instructions for the machine you
are going to use with this equipment and follow the safety measures
indicated.
2. GENERAL DESCRIPTION AND APPLICATIONS
The UC317S DISH DRAINER ROUTING DEVICE is designed to be used
with the UF317S/UFN317S parallel cutting and fastening equipment
4
E N G L I S H
and the FRE317VD angle trimmer, which are especially appropriate for
working with mineral-based materials such as Corian, Rausolid etc.
Applications:
• The UC317S equipment for routing channels in countertop dish
drainers, in combination with the UF317S/UFN317S parallel cutting
and fastening equipment, enables us to create several channels in
Corian countertops in order to make a dish drainer, using the UC317S
equipment as a guide and a FRE317VD router to cut them (Fig. 3 and 4).
• The UF317S/UFN317S parallel cutting equipment also enables us to
make parallel cuts by sliding the machine along its guide rail (Fig. 10)
and to perform other tasks that require attaching the machine base
to the part being worked on, such as when correcting small defects in
the material. The base of the machine may be attached directly to the
rail (Fig. 10), or by using the two suction pads mounted on each side
of the machine and on the part (Fig. 11).
3. STANDARD EQUIPMENT
The box contains the following items:
1. UC317S DISH DRAINER CHANNEL ROUTING DEVICE
2. 1746268 Template guide assembly for channels
3. UCP90 Suction pad
4. 3-mm Allen key
5. Operating instructions and miscellaneous documentation
4. OPTIONAL ACCESSORIES
1745838 UF317S Parallel cutting and fastening equipment
1746846 UFN317S Parallel cutting
1706539 Complete 650-mm rail
9045754 Complete 1.40-m rail
9045755 Complete 2.40-m rail
6046672 UCP90 Suction pad
6045710 Set of 2 holding G-clamps
9045812 UCP90 rail joint kit
5046437 Set of 2 units V-clamp.
5. USING THE UC317S DISH DRAINER
CHANNEL ROUTING DEVICE
5.1. RAIL PREPARATION
From the UF317S/UFN317S parallel cutting and fastening equipment,
select the rail (A) measuring 650 mm, which includes the millimetre
ruler (B) (Fig. 1).
First, insert the guide bar (C) with the fixing clamp (D) into one end
of the slot indicated on the millimetre rail (A), until it is in the correct
position. Then turn the tightening knob (E) to fasten the assembly to
the rail (Fig. 1).
5.2. MOUNTING THE UC317S CHANNEL
ROUTING DEVICE ON THE RAIL
Position the base (F) (Fig. 2) of the channel routing device under the
fixing clamp (D) (Fig. 1) and fasten it firmly in place, using the service
key to tighten the two screws (G) (Fig. 2). Rest the entire assembly
on the countertop so that the rail is positioned over the sink and the
channel milling machine is over the area of the dish drainer (Fig. 2).
The position of the channel routing device on the rail will depend on
the dimensions of the sink and the space available on the dish drainer
in order to securely fasten the equipment and comfortably perform
the milling of all channels.
To aid in this aspect, the equipment has been specially designed so
that the milling machine, once positioned on the channel milling
equipment, may be used from either right to left (Fig. 3) or left to right
(Fig. 4). Before attaching the rail to the countertop, it is necessary to
analyse where the start and end of each channel will be located in
each case, in order to ensure that it will be correctly milled along its
entire length.
When the machine operates from right to left, the rail must be positioned
over the sink, at least 170 mm (approximately) from the inside edge of
the sink (Fig. 3). On the other hand, when the machine operates from