Charger Operation - Lincoln PowerLuber 1880 Guía De Instalación Y Mantenimiento

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Cartridge
To fill gun from bulk
container
1 Remove pump assembly from grease tube
assembly.
2 Pack lubricant into cavity of the pump
assembly.
3 Insert the open end of the grease tube
assembly into lubricant. Slowly pull the
follower handle back while pushing the
grease tube assembly deeper into the lu-
bricant to prevent air pockets from being
pulled into the grease tube.
4 With the follower rod fully extended, pull it
sideways to latch the rod groove into the
slot in the grease tube assembly cap.
5 Loosely assemble the pump to the grease
tube assembly. Release the follower rod
from the grease tube assembly cap and
disengage the follower rod from the fol-
lower by rotating the follower handle.
6 Push the follower rod into the grease tube
assembly.
7 Unscrew the grease tube assembly from
the pump until lubricant oozes from the
interface. Tighten grease tube assembly
into the pump assembly.
8 Reset display reading after purging air.
9 Refer to the section titled
LCD display and LED light, († page 6).
To order call 1-800-548-1191 or visit www.partdeal.com - info@partdeal.com
Bulk
To fill gun with filler
pump
1 Engage the follower rod with the follower
by rotating the follower handle.
2 Insert the gun bulk fill valve into the filler
pump socket.
3 Operate the filler pump to fill the contain-
er. When the follower rod groove is ex-
posed, the grease tube assembly is filled.
The follower rod will be extended approx-
imately 20 cm (8 in.). Do not overfill!
4 Disengage the follower rod from the
follower by rotating the follower handle.
5 Push the follower rod into the grease tube
assembly.
6 Reset display reading after purging air.
!
Notice
Remove air pocket! Air pocket at
grease inlet will prevent grease from
being pumped. Unscrew the vent valve
three to four turns to remove small air
pockets trapped in this area. If the air
pocket is substantial and no grease
flows from coupler after trigger is pulled
for 15 seconds, refer to the following
steps.
8
To expel air pockets
Fig. 4
(air purging)
1 Withdraw the follower rod from the
grease tube assembly cap and engage it
with the follower by rotating the follower
handle.
2 Unscrew the plug of vent valve 3 to 4
turns. Exert force on the follower handle
until grease flows through the small hole
in the side of the vent valve.
3 Tighten the vent valve.
4 Pull the trigger in short bursts to operate
gun until trapped air is expelled. Disen-
gage the follower rod from the follower by
rotating the follower handle. Push the fol-
lower rod into the grease tube assembly.
5 If step 2 fails, unscrew the grease tube
assembly 3 turns from the pump
assembly.
6 Exert force on the follower handle until
lubricant oozes from the grease tube
assembly and pump assembly interface.
7 Retighten grease tube into the pump
assembly. Disengage the follower rod
from the follower by rotating the follower
handle. Push the follower rod into the
grease tube assembly.

Charger operation

Charging battery pack
Before using your PowerLuber for the first
time, the battery pack should be fully
charged. If the battery pack is installed in the
PowerLuber, remove it and follow charging
procedure below.
Lincoln chargers are designed to charge
Lincoln lithium-ion batteries in 30 to
90 minutes depending on the battery's state
of charge and temperature.

Publicidad

Capítulos

Tabla de contenido
loading

Este manual también es adecuado para:

Powerluber 1882Powerluber 1882ePowerluber 1884Powerluber a serie18801882 ... Mostrar todo

Tabla de contenido