Yokis TLC2C Manual De Instrucciones página 9

RADIO TRANSMITTERS
E2BPX 5454408 2-channel transmitter with external aerial
tLC8C 5454403 8-pushbutton remote control
POWER RANGE
E2BPP 5454413 2-channel flush-mounted POWER transmitter
2-channel flush-mounted POWER transmitter
E2BPPX 5454414
POWER with external aerial
E4BPP 5454427 4-channel flush-mounted POWER transmitter
E4BPPX 5454428 4-channel flush-mounted POWER transmitter
with external aerial
TLC4CP 5454425 4-pushbutton POWER remote control
TLC8CP 5454423 8-pushbutton POWER remote control
GALET8TP 5454424 8 pushbutton flat POWER remote control
GALETBOISP 5454426 8 pushbutton deluxe flat POWER remote control
1-pushbutton wall-mounted POWER remote
TLM1T45P
5454417
control
2-pushbutton wall-mounted POWER remote
TLM2T45P
5454419
control
4-pushbutton wall-mounted POWER remote
TLM4T45P 5454421
control
TLC1TP 5454430 1-pushbutton Power remote control of Design
TLC2TP 5454431 2-pushbutton Power remote control of Design
TLC4TP 5454432 4-pushbutton Power remote control of Design
4-pushbutton flat POWER remote control of
GALET4TP 5454433
Design
technical specifications:
- CR2032 Lithium battery (included)
- Battery life > 7 years
- Max. 4 receivers per transmitter button
- Operating temperature: from -10 to + 50°C
- IP54 protection
- Max. relative humidity 80%
- Frequency: 2,4 GHz
- Transmission: two-way
WARNING: Explosion risk if the battery is replaced with a battery other
than the referred one. Dispose of the used batteries as per local stan-
dards.
E2BPP E4BPP
D I R E C T M O D E
1
Press the pushbutton to be connected on the
transmitter (E) 5 times**.
The transmitter LED will start flashing for 30
seconds, indicating that the system is waiting
for connection.
** Each press must last less than 0.7 seconds
2
Briefly press the pushbutton in the 'connect' hole
of the receiver (R) (on the front or the back of the
receiver) with the point of a pencil while the
transmitter LED is flashing.
The transmitter LED will stop flashing.
Warning: the receiver must be powered.
DS1054-009H
The E2BPP/E4BPP may be wired behind pushbuttons (or switches) of any model.
Wiring both channels is not indispensable: a single pushbutton can be used con-
nected to a single channel.
Switches can be used instead of pushbuttons to drive Mtr2000ErP
receivers. In this case, switch 5 times rapidly (not 10!) instead of using the 5
press sequence. Repeat the connection procedure by pressing 5 times to use a
pushbutton again instead of the switch.
GB
radio raNGE:
Standard range:
• In the same room (< 100 m²)
• 50m in open range
(Range may be reduced by presence of metallic
elements, crossing of walls or partitions)
Power range:
• Inside 100m² apartments with perpendicular
crossing of main wall or ceiling
• 250m in open range
(Range may be reduced by presence of metallic
elements, crossing of walls or partitions)
radio traNSMiSSioN:
the transmitter LEd lights up only if radio
transmission was successful.
Adding an intermediate receiver will allow to solve a
problem of insufficient range (see § "How to increase
the range").
the LEd will light up on transmitters
only if radio transmission was successful
Simply repeat the same procedure
all YoKiS transmitters are compatible with
(relays, dimmer and Shutter Modules).
P8
to delete a connection
YoKiS receivers
GB ES