General Maintenance - Far Tools GGC 950 Traduccion Del Manual De Instrucciones Originale

EN
GENERATOR SET OVERLOAD
Never exceed the rated power capacity (Amperes and/
or Watts) during continuous operation. Before connecting
and running the generator set, calculate the electrical
power consumption of the electrical equipment (in Watts
or Amperes). This electrical power (in Watts and/or Amperes)
is generally found on the identification plate of bulbs, elec-
trical appliances, motors, etc. The total of all the powers of
the equipment used should not exceed at any one time the
rated power of your generator set.
Note: an electrical appliance (compass saw, drill, etc.) consu-
mes more Watts or Amperes than the number specified on
the identification plate when the motor is subjected to diffi-
cult use. For example, a saw that is to cut an extremely hard
material consumes 3 to 4 times more Watts or Amperes
than the number specified on its identification plate.
STARTING UP, OPERATING AND SHUTTING DOWN THE
GENERATOR SET
Starting up the generator set
a) Open the petrol cock by turning the handle (17) to «ON»
b) Close the starter by pushing the lever(18).
c) Set the on/off switch (13) to «ON».
d) Take hold of the start-up handle correctly.
e) Pull the start-up handle slowly until a slight resistance is
felt and then return it slowly.
f) ake hold of the start-up handle correctly and pull the cord
firmly and quickly (pull it completely and use both hands
if required).
Return the handle slowly by hand. If the motor has not
started, repeat the operation until the motor has started by
opening the starter progressively.
Check the condition of the rope. For your safety, if it shows
signs of wear, closer to the point of sale.
g) When the motor has started up, open the starter pro-
gressively.
Before making any attempt to start up the
generator set, make sure that all the instructions
described in the above sections have been strictly
adhered to.
Before starting the engine, do not connect the
electric apparatus.
Unregulated voltage can cause damage to elec-
tronic equipment.
118015-2-Manual-K.indd 12
DVD
VHS
OPERATING THE GENERATOR SET
a) When the generator has stabilised its speed (1 min),
connect the male connector(s) into the female connector of
the AC generator.
Press into the AC protector and turn on teh electric appa-
ratus
N.B : Press to reset the AC protector.
1: «ON» 2: «OFF»
From this moment, you can use your electrical equipment.
-Be sure all electric apparatuses including the
lines and plug connection are in good condition
before connection to the generator.
-Be sure electric apparatus is turn off before
plugging it in.
-Be sure the total load is within generator rated
output.
-Be sure the socket load current is wthin socket
rated current.
SHUTTING DOWN THE GENERATOR SET
a) Disconnect the connectors to allow the motor to run off-
load for 1 or 2 min. Set the on/off switch (13) to «OFF»: the
generator shuts down
b) Close the petrol cock.(17)
Reduce the load to the specified generator rated
output if the AC protector turns off. If it turns off
again, consult your FARGROUP dealer.

GENERAL MAINTENANCE

TOUS LES ENTRETIENS S'EFFECTUENT
LE GROUPE ÉLECTROGÈNE À L'ARRÊT,
BOUGIE DÉCONNECTÉE.
AIR FILTER MAINTENANCE
CLEAN THE FILTER EVERY 100 HOURS OR EACH SEASON
-Unfasten the screws from the cover of the air filter (12).
-Remove the cover and the complete air filter from the base.
-Remove the complete air filter from the cover
SILENCER
You should periodically remove the Carbon deposits.
1- Remove the muffler protector.
2- Remove the muffler
3- Remove the Carbon deposits using a wire brush and by
trapping the muffler body lightly.
4- Reinstall the muffler.
SETTING THE SPARK PLUG
CLEAN AND SET THE DISTANCE OF THE SPARK PLUG
ELECTRODES EVERY 100 HOURS OF OPERATION (DISTANCE:
0.8 MM)
-The spark plug is only
cleaned with a scraper
or a metal brush plus a
clean cloth (replace it if
required)
EN
23/07/15 15:31:09