JB Systems LED Diamond Manual De Instrucciones página 5

ENGLISH
AUTOMATIC MODES:

Connect nothing to the DMX input of the LED DIAMOND

Press the MENU button to browse the different automatic color modes. You can choose one of
the following modes:
o A1: red
A2: green
o
A3: blue
o
o A4: green – blue – red alternating
o A5: 7 colors alternating
A6: fading colors
o
A7: strobe effect
o
 When you have reached the color mode you would like to use, then use the UP and DOWN
buttons to select a rotation speed between 1 and 9.

When the setting of the speed is done, press the ENTER button to confirm.

The LED DIAMOND will now run your selection.
SOUND CONTROLLED MODES:

Connect nothing to the DMX input of the LED DIAMOND

Press the MENU button to browse the different sound controlled modes. You can choose
between the following modes:
So 1: sound controlled color mode
o
So 2: sound controlled strobe mode
o

Press the ENTER button to confirm your choice.
MASTER / SLAVE MODE:
Select this function when you want an instant show. By linking the units in master/slave connection, the first
unit will control the other units to give an automatic or sound activated, synchronized light show.

Connect nothing to the DMX input of the first LED DIAMOND, because this will be the Master Unit.

Select in this Master unit one of the automatic or sound controlled modes like mentioned in the
previous chapter 'STANDALONE MODE"
 Set the DMX address of all the other LED DIAMOND units (also called 'slave' units) on d.001. Follow
these steps to set the DMX address:
 Press the MENU button until d.xxx or Axxx (d. or A followed by 3 numbers) appears on the
display

Press 2 times the ENTER button. --> the actual DMX address will appear on the screen (a
number between 1 and 512)

Use the UP & DOWN buttons to select address 001

Press the ENTER button to confirm. d.001 or A001 will appear on the display what means that
the unit is now in DMX mode, that it has start address 001 and that it is waiting for information
from the master unit to be activated.
DMX MODE:
The LED DIAMOND can be controlled by any universal DMX controller via 1 DMX channel or via 6 DMX
channels.
This is how you set the DMX channel mode + the DMX start address:
 Press the MENU button until d.xxx or Axxx (d. or A followed by 3 numbers) appears on the display

Press the ENTER button.

--> 1 Ch or 6 Ch will appear on the display.

Use the UP & DOWN buttons to select the desired channel mode:
1 Channel Mode: this easy mode is used to select different build-in programs via 1 DMX
o
channel. (see DMX chart for more information)
o 6 Channel Mode: in this mode you have total control over strobe + colors & dimming +
rotation speed or you can select some automatic functions (see DMX chart for more
information)

Press the ENTER button to confirm your channel mode.

--> 3 numbers will appear. This is the DMX start address. Use the UP & DOWN buttons to select the
DMX address you would like to use.

Press the ENTER button to confirm.
 Ready.
JB SYSTEMS
®
OPERATION MANUAL
5/42 LED DIAMOND
ENGLISH
If you have selected the 1 Channel option: d.xxx (d. followed by the 3 numbers of the DMX address) will be
written on the display.
If you have selected the 6 Channel option: Axxx (A followed by by the 3 numbers of the DMX address) will
be written on the display.
DMX CHARTS:
6 CHANNEL MODE
DMX Channel Function DMX Value
000 - 005
CH 1 STROBE
006 - 255
000
CH 2 RED
001 - 255
000
CH 3 GREEN
001 - 255
000
Ch 4 BLUE
001 - 255
000 - 127
Ch 5
MOTOR
128 - 255
000 - 005
Ch 6 AUTOMATIC 006 - 250
251 - 255
1 CHANNEL MODE
DMX Channel DMX Value
000 - 029
030 - 059 Mode A5 1: Alternating colors at speed 1
060 - 089 Mode A5 4: Alternating colors at speed 4
090 - 119 Mode A5 9: Alternating colors at speed 9
120 - 149 Mode A7 1: Strobe effect at speed 1
Ch 1
150 - 179 Mode A7 4: Strobe effect at speed 4
180 - 209 Mode A7 9: Strobe effect at speed 9
210 - 239 Mode SO1: sound controlled color mode
240 - 249 Mode SO2: sound controlled strobe mode
250 - 255
MAINTENANCE
 Make sure the area below the installation place is free from unwanted persons during servicing.
 Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
 All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
 Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
 When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
 The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
 In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.
 The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
 The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit's optics.
 Clean with a soft cloth using normal glass cleaning products.
 Always dry the parts carefully.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
JB SYSTEMS
®
OPERATION MANUAL
Full ON / Strobe off
Strobe speed (fast to slow)
OFF
Dimmer (low to full power)
OFF
Dimmer (low to full power)
OFF
Dimmer (low to full power)
Position
Rotation (slow to fast)
Manual Mode (CH1 to CH 5 active)
Automatic Modes (fast to slow)
Sound Controlled Mode
BLACKOUT
Random Show A1 to A7
6/42 LED DIAMOND