Using The Setup Menu - Insignia NS-DVDR1 Guia Del Usuario

Ocultar thumbs Ver también para NS-DVDR1:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Menu
Available options
• DISC: Displays the Photo menu for
Photo
a disc.
(See "Photo
List menu
options" on
page 19)
• DISC: Displays the Music (or Audio
Music
CD) menu for a disc.
(See "Audio
CD and Music
menu options"
on page 18)
• Dubbing: Displays the Dubbing
menu.
• Disc Manager: Displays the Disc
Setup menu.
Easy Menu
• Rec. Mode: Displays the Record
Mode setup menu.
• DV Input: Changes to DV Input
mode.

Using the Setup Menu

In this menu system there are several ways to
customize the settings. Most menus consist of
three levels to set up the options, but some
require more levels for some settings.
To change settings using the Setup menu:
1 Press HOME. The Home menu opens.
2 Select SETUP and Start, then press ENTER.
The Setup menu opens with the General
Settings icon highlighted.
3 Press
/
to select the option you want,
then press
4 Press
/
to select the second option you
want, then press
level.
5 Press
/
to select the setting you want,
then press ENTER to confirm your selection.
Some items require additional steps.
6 Press
RETURN or HOME to exit the
Setup menu.
Note
Press
to go back to the previous level.
14
to move to the second level.
to move to the third
www.insignia-products.com
Menu
Available settings
General
Tuning Band–You can select
CATV.
Settings
Auto Channel Set–Press
auto channel selection.
CH. Add/Del–You can manually add or
erase channels from memory.
Clock Set–You can manually or
automatically (using XDS) set the clock.
TV Aspect–You can select from 4:3
Letter box, 4:3 Pan scan, or 16:9 Wide.
Progressive Scan
progressive scan video, which provides
the highest quality pictures with less
flickering.
If you are using the Component Video
Out/ Progressive Scan jacks, but are
connecting the recorder to a standard
(analog) television, set Progressive Scan
to OFF.
If you are using the Component Video
Out/ Progressive Scan jacks for
connection to a TV or monitor that is
compatible with a progressive scan
signal, set Progressive Scan to ON.
Caution: Once the setting for progressive
scan output is entered, an image will only
be visible on a progressive scan
compatible TV or monitor. If you set
progressive scan to ON by mistake, you
must reset the recorder. To do this,
remove the disc, then press STOP (
and hold it for five seconds before
releasing it. The video output will be
restored to the standard setting, and a
picture will once again be visible on a
conventional analog TV or monitor.
Power Save Mode–You can set Power
Save Mode to ON to enable an economic
power save mode.
Factory Set–You can reset your recorder
to original factory settings.
Language
Display Menu–You can select a
language for the setup menu and
Settings
information display.
Disc Menu–You can select a language
for the DVD menu.
Disc Audio–You can select a language
for the DVD audio.
Disc Subtitle–You can select a language
for the DVD subtitle.
Audio
Dolby Digital/DTS/MPEG–You can
select Bitstream (if you connect to
Settings
equipment with Dolby Digital, DTS, or
MPEG decoder), or PCM (to
automatically downmix to two-channel
PCM audio).
Sampling Freq.–You can select 96 kHz
or 48 kHz (if your receiver or amplifier is
not capable of decoding 96 kHz signals).
DRC (Dynamic Range Control)–You
can set the DRC to On if you want to
listen to a movie at a lower volume,
without losing clarity.
Vocal–You can set the Vocal to ON when
a multi-channel karaoke DVD is playing.
This mixes the karaoke channels on the
disc into normal stereo sound.
NS-DVDR1 DVD Recorder
TV
or
Start
to begin
You can turn on
)

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido