Craftsman 917.28671 Manual Del Operador página 17

ACION
_., 1-)Accesorio
de Grasa der
rbol
(_) Accesorio
de Grasa del
Rodarniento
e la Rueda
Delantera
Motor
OTOR" en Man-
_elos puntos piv-
le nil6n especiaF
._r,_n polvo y mu-
los rodamientos
nte un lubricante
rma moderada.
TRACTOR
Always observe safety rules when performing
any maintenance°
BRAKE OPERATION
If tractor requires more than five (5) feet to
stop at highest speed in highest gear on a
level, dry concrete or paved surface, then
brake must be serviced. (See "TO CHECK
BRAKE" in the Service and Adjustments
section of this manual).
TIRES
• Maintain proper air pressure in all tires
(See PSt on tires).
, Keep tires free of gasoline, oil, or insect
control chemicals which can harm rubber.
, Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may cause
tire damage°
NOTE: To sealtire punctures and preventfiat
tires due to slow leaks, tire sealant may be pu r-
chased fro m your local parts dealer. Tire seal-
ant also prevents tire dry rot and corrosion.
OPERATOR PRESENCE SYSTEM AND
REVERSE OPERATION SYSTEM (ROS)
Be sure operator presence and reverse
operation systems are working properly° If
your tractor does not function as described,
repair the problem immediately.
. Theengineshould notstartunlessthe brake
pedal isfully depressed, andthe attachment
clutch control is inthe disengaged position.
CHECK OPERATOR PRESENCE SYSTEM
• When the engine is running, any attempt
by the operator to leave the seat without
first setting the parking brake should shut
off the engine.
• When the engine is running and the at-
tachment clutch is engaged, any attempt
by the operator to leave the seat should
shut off the engine.
o The attachment clutch should never oper-
ate unless the operator is in the seat.
Ros "On"
Position
Engine "On" Position
(Normal Operating)
CHECK REVERSE OPERATION SYSTEM
° When the engine is runningwiththe ignition
switch in the engine "ON" position and the
attachment clutch engaged, any attempt
by the operator to drive in reverse should
shut off the engine.
. When the engine is running with the ignition
switch in the ROS "ON" position and the
attachment clutch engaged, any attempt
by the operator to drive in reverse should
NOT shut off the engine.
BLADE CARE
For best results mower blades must be sharp,
Replace worn, bent or damaged blades.
,& CAUTION: Use only a replacement blade
app roved by the manufacturer of your tractor.
Using a blade not approved by the manu-
facturer of your tractor is hazardous, could
damage your tractor and void your warranty_
BLADE REMOVAL
1. Raise mower to highest position to al-
low access to blades°
NOTE: Protect your hands with gloves
and/or wrap blade with heavy cloth.
2. Remove blade bolt by turning counter-
clockwise°
3o Install new blade with stamped
"GRASS SIDE" facing the ground°
IMPORTANT: To ensure proper assembly,
center hole in blade must align with star
on mandrel assembly.
4r Install and tighten blade bolt securely
(45-55 Ft. Lbs. torque)°
IMPORTANT: Special blade bolt is heat
treated.
Blade
Center Hole
Mandrel
BATTERY
Your tractor has a battery charging system
which is sufficient for normal use, How-
ever, periodic charging of the battery with
an automotive charger will extend its life_
, Keep battery and terminals clean_
, Keep battery bolts tight.
. Keep small vent holes open.
• Recharge at 6-!0 amperes for 1 hour:
NOTE: The original equipment battery on
your tractor is maintenance free. Do not
attempt to open or remove caps or covers.
Adding or checking level of electrolyte is
not necessary,
TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and termi_
nals can cause the battery to "leak" power.
1. Disconnect BLACK battery cable first
then RED battery cable and remove
battery from tractor,
2. Rinse the battery with plain water and dry,
3o Clean terminals and battery cable
ends with wire brush until bright°
4. Coat terminals with grease or petroleum
jelly°
5. Reinstall battery (See "REPLACING
BATTERY" in the SERVICE AND AD-
JUSTMENTS section of this manual).
17