Novellini Divina Manual De Instalación, Uso Y Mantenimiento página 44

INTRODUCTION:
Whirlpool baths must be installed by trained personnel able to demonstrate to the
relevant authorities their knowledge and ability in the application of health and
safety regulations i.e. electricity and water supplies and waste water disposal. The
manufacturer provides training for technical assistance staff and therefore you are
advised to contact an authorised technical assistance centre for the purposes of
installation.
This symbol indicates important product instructions or important safety
information.
INSTALLATION:
IMPORTANT!
Before you start to assemble and install the product, carefully read through all the
instructions. Unpack the components and check that nothing is missing and that there
are no damaged or faulty components, remove the transparent protective film.
All components requiring maintenance (e.g. pump, electrical components, etc) must
remain accessible once final installation is complete.
Do not support the bath using the hoses during transport.
N.B.: This product is designed for installation on finished walls and floors.
Warranty claims must be produced with the purchase invoice and the product
assembling instructions.
The drawings and illustrations in this manual are provided for information purposes
only.
The manufacturer reserves the right to make changes and improvements without prior
notice.
INSTALLATION OF BATH WITH FRAME:
Follow the sequence of drawings given in this manual very carefully when installing a
bath with frame.
INSTALLATION OF ENCLOSED BATH:
Before building the enclosing walls, it is best to position the bath and make the required
connections. The wall can extend inwards under the lip of the bath by not more than
1.5 cm. The drain must be connected in such a way that the bath can be pulled out of
the enclosure for maintenance, when necessary. To facilitate this operation do NOT fix
enclosed type baths to the floor. In this case, fix the bath by applying silicone on all four
sides (see siliconing illustration on page 39).
Inspection panel required.
(I)
OPERATING TEST:
An operating test must be performed following installation. Check that the bath is clean.
Fill the bath with water at an infeed temperature of 40°C (± 5°C) up to a level above
the highest nozzle to allow the system to function.Switch on the system and run it for
10 minutes. Switch OFF the whirlpool function but do not empty the bath and after 10
minutes check all the hoses, couplings, etc. for any leaks.
The test should be repeated following any adjustments or substitutions. Backflow of
water towards the mains water supply must be avoided to ensure conformity with EN
1
2
3
1717 when filling the bath. Therefore if the taps are fitted so that the water fills the bath
from above the top of the bath then the taps must be positioned (at least in terms of
height) in accordance with the diagrams shown from page 29.
If the system involving a combined water inlet and overflow outlet is used to fill the
bath, a water outlet spout consisting of a non-return valve (not supplied) must be fitted
between the combined tap water inlet point and the delivery system located on the
discharge column.
CLEANING AND DISINFECTING:
During use, small organic particles are deposited in the whirlpool pipes and if not treated
may lead to proliferation of bacteria in the system. For perfect hygiene, you should treat
the system with specific products available from our Service Centres (see updated list
on our site www.novellini.com under the heading "Service") or dealers specialising in
products for whirlpool baths. For temporary treatment you can use a liquid disinfectant
(eg. Dettol). How to clean the bath. You should also perform a specific treatment if
the bath is left unused for long periods. If the bath is used by more than one person
consecutively, you are recommended to disinfect after each cycle.
You should never use or take a bath in the water used for disinfecting.
CLEANING AND DISINFECTION:
Deposits of organic material that collect in the pipes during a whirpool bath promote
bacterial growth and, if left untreated, cause unsanitary conditions and unpleasant
odours. For perfect hygiene, the jets system should be disinfected immediately after
bathing, before draining. To disinfect, use 50 g of ordinary disinfectant (for example,
liquid bleach) for every 100 litres of water (approximately half a glass in a bath filled
to optimum level). Run the system for few minutes to circulate the disinfectant in the
pipes. Stop the system, allow to soak for 15/20 minutes, then drain the bath. If the bath
develops unpleasant odours after a long period of inactivity, it's a good idea to disinfect
the system before using it again. For hygiene, if the bath is used consecutively by two or
more people, the system should be disinfected after each use. During disinfection, turn
off the air control to reduce foaming.
MAINTENANCE AND CLEANING:
The bath is made of acrylic and must be cleaned using a liquid detergent and a soft cloth
or sponge. Use a good quality household liquid detergent. To prevent scale deposits,
wipe dry using a chammy leather or a soft lint-free cloth that removes stubborn
deposits without leaving traces. Limescale deposits may be removed using specific
detergent products. To restore shine to the acrylic surface polish with an ordinary wax
polish such as car wax.
DO NOT USE ABRASIVE CLEANERS, ALCOHOL OR ALCOHOL BASED PRODUCTS, ACETONE
OR OTHER SOLVENTS.
Warning: use of detergents other than those recommended may damage the bath
and/or the whirlpool equipment.
SURFACE SCRATCHES:
Small surface scratches can be removed using wet emery paper (grade 1000) and then
smoothing the surface with abrasive paste. Once the scratch has been removed, restore
surface shine using wax polish. For the best results, contact your nearest authorised
service centre.
TROUBLESHOOTING:
In the event of a problem, perform the following checks before calling the service centre.
If the jet system does not stop:
• If the pump continues running and cannot be turned off using the usual controls, turn
it off using the circuit breaker and try again. If the problem persists, contact the service
centre.
Do not attempt to make adjustments to the wiring or other electrical
parts under any circumstances. Always contact your nearest service centre.
-44-
ENGLISH