Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Read the instructions carefully before using the product, and
keep them for future consultation
The User must not in any way attempt to repair or to take direct
action and must solely contact qualified FAAC personnel or
FAAC service centres.
GENERAL SAFETY REGULATIONS
If used correctly, the automation will ensure a high degree of
safety.
Some simple rules regarding behaviour will avoid any accidental
trouble:
1.
Do not pass through the leaves while they are moving. Before
passing through the leaves, wait until they are fully open.
2.
Do not, on any account, stand between the leaves.
Do not stand near the automation and do not allow children
3.
and other people to stand there, especially while it is ope-
rating.
Keep remote controls or any other pulse generator well away
4.
from children to prevent the automation from being activated
involuntarily.
5.
Do not allow children to play with the automation.
6.
The application cannot be used by children, by people with
reduced physical, mental, sensorial capacity, or by people
without experience or the necessary training.
7.
Do not willingly obstruct movement of the leaves.
8.
Do not allow branches or shrubs to interfere with leaf move-
ment.
9.
Keep illuminated signalling systems efficient and clearly visi-
ble.
10.
Do not attempt to activate the leaves manually unless you
have released them first of all.
11.
In the event of a malfunction, release the leaves to allow
access and wait for qualified personnel to take appropriate
action.
12.
After enabling manual operating mode, switch off the power
supply to the system before restoring normal operating
mode.
13.
Do not make any alterations to the components of the au-
tomation.
The User must not in any way attempt to repair or to take direct
14.
action and must solely contact qualified FAAC personnel or
FAAC service centres.
Call in qualified personnel at least every 6 months to check
15.
the efficiency of the automation, safety devices and earth
connection.
DESCRIPTION
These instructions apply to the following model:
The 770 automation system for swing gates is a geared motor. It is
designed for underground installation and therefore does not alter
the appearance of the leaf.
The foundation box of the automation system comes ready to
take an operator.
The 770 electromechanical operator is irreversible, so it ensures
a mechanical stop and eliminates the need to install an electric
lock.
A manual release makes it possible to move the gate in the event
of a power-cut or fault.
Fig. 1
Fig. 1
770
The operators are supervised by an electronic control unit, housed in
a container adequately protected against atmospheric agents.
The leaves are normally in closed position.
When the electronic control unit receives an opening command
by remote control or by any other pulse generator, it activates
the operator to rotate the leaves until they are sufficiently open
to provide access.
If automatic operating mode was set, the leaves close on their
own after the selected pause time has elapsed.
If semi-automatic operating mode was set, a second pulse must
be sent to allow the leaves to close again.
A stop pulse (if supplied) always stops movement.
For detail on operation of the automation under different opera-
tional logics, consult the installation technician.
The automations include safety devices (photocells, sensitive
edges,...) which prevent the leaves from moving when there is an
obstacle in the area they protect.
The light indicates that leaves are moving.
MANUAL OPERATING MODE
Should the need arise to operate the gate manually because of a
power failure or malfunction, the release device with key fitted on
the support bracket makes it possible to release the system both
from the inside and from the outside.
To operate the leaf manually, proceed as follows:
Cut power to the system.
•
open the lid of the lock (Fig. 1 rif. a)
•
insert the release key in the lock (Fig. 1 rif. b)
•
turn the key in the direction of the post, as far as it will go (Fig.
1 rif. c)
•
pull the lever out (Fig. 1 rif. d)
•
operate the leaf manually.
RESTORING NORMAL OPERATING MODE
To avoid an involuntary pulse from activating the gate during
the manoeuvre, before re-locking the operator , switch off
power to the system.
•
push the lever back into its home position (Fig. 2 rif. a)
•
insert the release key in the lock and turn it in the direction opposite
the post, as far as it will go (Fig. 2 rif. b)
•
operate the leaf manually until the lock is engaged in the locking
bracket (Fig. 2 rif. c)
•
close the lid of the lock.
•
make sure that the gate cannot be moved manually.
•
restore power to the system.
770
Page
Instructions for use
Fig. 2
Fig. 2
Publicidad
Tabla de contenido
