Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Transmitters enable the user to control one or more
motors with receiver, installed on awnings, shutters and
screens. It is possible to set them up in order to create
group commands and let more motors work simulta-
neously.
The radio signal is shown by the transmission LED. If
the LED doesn't blink after the button pressure, then the
battery has to be replaced.
PLEASE NOTE: do not use motors with remote controls
in areas with risks of radio disturbs over the norm (i.e.
airports or radio repeaters). These units may also be
disturbed by telecommunication and/or transceiver
systems with the same frequency.
PROGRAMMING TRANSMITTER/CHANNEL (Fig.1)
CAUTION: If more motors with receiver have to be
installed, it is important to power up only one motor at
time during the first programming session, in order to
avoid any interferences with the others.
Power up the motor to be programmed.
1.A [with QCTX2/5] Select the channel to be program-
med by pressing SEL (6).
1. Hold PROG-TX (4) pressed until the motor starts
moving.
2. Check the rotation of the motor, then release PROG-
TX (4) (the motor stops).
3. Within 5 seconds press the corresponding button (i.e.
UP (1) if the motor rotates upwards or DOWN (3) if
vice versa).
In this way the transmitter/channel has been program-
med and the rotation of the motor has been syncronized.
ADDING TRANSMITTER/CHANNEL
[With QCTX2/5] Select the channel to be added by pres-
sing the SEL (6).
1. Hold PROG-TX (4) pressed of a transmitter
already paired until the motor starts moving.
2. Check the rotation of the motor, then release PROG-
TX (4) (the motor stops).
3. Within 5 seconds press the corresponding button (i.e.
UP (1) if the motor rotates upwards or DOWN (3) if
vice versa) on the new transmitter being added.
Additional transmitter/channel is now added.
CHECKING/CHANGING DIRECTION (Fig.2)
1. Press UP (1) or DOWN (3) the motor should go up-
ward or downward, otherwise to change direction:
2. Press and hold PROG-TX (4) button till the motor
starts moving.
3. Press STOP (2): The motor makes a brief jog.
Direction of the motor has been reversed.
IMPORTANT: the change of direction of operation must
be performed before initiating limit setting procedure
otherwise limits must be reset
ERASING TRANSMITTER/CHANNEL
[QCTX2/5] Select the channel to be erased by pressing
the SEL button (6).
Push simultanously PROG-TX (4) and STOP (2) of the
transmitter until the motor makes a brief movement in
both directions.
Only the transmitter used (or the channel selected) for
this procedure has been deleted from motor memory.
RESET TRANSMITTER MEMORY (DELETING ALL THE
TRANSMITTERS OR CHANNELS OR SENSORS)
OPTION 1 (Fig. 3.1)
Using an already programmed transmitter press and
hold both PROG-TX (4) and STOP (2) buttons till the
motor makes first a brief jog and, after a while, a second
long jog.
Memory is now empty.
OPTION 2 (Fig. 3.2)
1. Without an already programmed transmitter switch
the motor power supply OFF. Then switch it ON.
2. Within 8 seconds, using any Gaposa transmitter,
press and hold both PROG-TX (4) and STOP (2) but-
tons until the motor makes a long jog.
Memory is now empty.
LIMIT SWITCH SETUP
(ATTENTION: Just for motors with electronic limit
switch).
ALWAYS SET THE UP (1) LIMIT SWITCH FIRST.
1. Push PROG-FC (5) till the motor makes a brief
movement in both direction
Note: during "programming mode" the operations
are in "deadman control"
2. Press and hold the UP (1) button and run the motor
to the desired UP (1) limit position.
3. Press STOP (2) to set the UP (1) limit position.
The motor makes a brief jog.
4. Press and hold the DOWN (3) button and run the
motor to the desired DOWN (3) limit position.
5. Press STOP (2) to set the DOWN (3) limit position.
The motor makes a brief jog.
Note: Accurate limit setting can be performed when
UPWARD or DOWNWARD by pressing a second time
PROG-FC (5): the motor then moves slowly in steps to-
wards to the desired limit. Always press STOP (2) button
to set the limit position
AUTOMATIC SETTING OF THE LIMITS
(Just for motors with electronic limit switch))
For limits set with torque sensor ( mechanical stop of
shutters or cassette awnings/shades), press and hold
UP (1) button until the bottom bar hits the cassette or
shutter box.
A short jog will indicate that the UP (1) position has been
memorized. The same procedure can be followed for
DOWN (3) limit but only for roller shutters.
Publicidad
