Problems Analysis And Solutions; Problems, Causes And Solutions; General Advices; Consejos Generales - Skymsen LT-2,0 SUPER GOURMET 2 Manual Instrucciones

5. PROBLEMS ANALYSIS and SOLUTIONS

5.1 Problems, Causes and Solutions

The Professional Blender has been designed to require minimum maintenance. However, some
performance failures may happen due to natural wearing caused by the use of the equipment.
If any problem arises with your Professional Blenders , check the
Table - 02 below, where there are some detailed and recommended possible solutions.
Problems
* The machine does * Lack of power or the
not turn On. plug is off the socket.
* Ploblem with the
internal or external
electric circuit of the
machine.
* Cup is leaking.
* Problems in the
sealing system.
* The product is too
big not allowing the
* The products do not
contact with the balde.
get processed.
* Blunt Blade.

6. GENERAL ADVICES

- Do not wear loose fitting clothes while operating the unit. Do not use bracelets or any other piece of
jewelry. Have your hair always shortened and held up (use hair fishnets if necessary) in a way it
cannot reach any part of the machine. Roll up any loose sleeves.
- SKYMSEN is not responsible for any harm or injury caused by the negligent or inappropriate use of
this equipment by any operator. This equipment must be operated only by persons whose age equals
or exceeds 18 years old, in a safe and sound state of mind, free from the influence of any kind of drugs
and alcohol, that received proper training and instructions regarding the correct operation of this
machine, that are wearing correct and authorized safety clothes. All and any kind of modifications
carried on and applied to this machine immediately nullifies any kind of warranty and may result in
harm and injuries to the individuals operating this machine and to individuals that are located in the
machine surrounding areas while it is being operated.
- Under no circunstances place your hands in the moving parts of the machine while it is being used.
Make sure the machine has come to a complete stop before acessing the processed ingredients.
Table - 02
Causes Solutions
* Check if the plug is
on the socket, and if
there is electric power.
* Call technical
assistance.
* Call technical
assistance.
* Cut the ingredients
into smaller pieces,
less than 2 cm size.
* Call technical
assistance.
09
–
5 Análisis y Resoluciones de Problemas
5.1 Problemas, causas y resoluciones.
Las Licuadoras Profesionales fueran diseñadas para necesitar un mínimo de manutención.
Sin embargo pueden ocurrir algunas irregularidades en su funcionamiento debido al desgaste natural
causado por su uso.
Caso ocurra algún problema verifique la Tabla 02 abajo donde están algunas soluciones
recomendadas. Además, el fabricante deja a su disposición una rede de Asistentes Técnicos Autorizados.
Problemas
* La maquina no prende.
*
Falta energía eléctrica el
enchufe está
*
Problema en el circuito
interno o externo de la
maquina.
*
Problema con el sistema
*Vaciamiento del vaso.
de vedamiento.
*El producto no se licua.
*
Pedazos muy grandes del
producto impiden el
contacto com la cuchilla.
*
Cuchilla no afilada.

6. CONSEJOS GENERALES

- Do not wear loose fitting clothes while operating the unit. Do not use bracelets or any other piece of jewelry. Have
your hair always shortened and held up (use hair fishnets if necessary) in a way it cannot reach any part of the
machine. Roll up any loose sleeves.
- SKYMSEN is not responsible for any harm or injury caused by the negligent or inappropriate use of this
equipment by any operator. This equipment must be operated only by persons whose age equals or exceeds 18
years old, in a safe and sound state of mind, free from the influence of any kind of drugs and alcohol, that received
proper training and instructions regarding the correct operation of this machine, that are wearing correct and
authorized safety clothes. All and any kind of modifications carried on and applied to this machine immediately
nullifies any kind of warranty and may result in harm and injuries to the individuals operating this machine and to
individuals that are located in the machine surrounding areas while it is being operated.
- Under no circunstances place your hands in the moving parts of the machine while it is being used. Make sure the
machine has come to a complete stop before acessing the processed ingredients.
Causas Soluções
*
Verifique si el enchufe
está conectado, y si hay
energía eléctrica.
*
Llame la asistencia
Técnica.
*
Llame la asistencia
Técnica.
*
Corte el producto en
pedazos menores, de
aproximadamente 2cm.
*
Llame la asistencia
Técnica.
18