Kichler RLM Instrucciones De Instalación

RLM WALL MOUNT
Installation Instructions
General Considerations:
Read all instructions and review diagrams before assembly.
This fixture is intended for installation in accordance with
the National Electrical Code (NEC) and all local code
specifications. If you are not familiar with code requirements
or have any doubts, installation by a qualified, licensed
electrician is recommended.
Mounting surface should be clean, dry, flat and 1/4" larger
than the Wall Mount on all sides. Any gaps between the
mounting surface and Wall Mount exceeding 3/16" should be
corrected prior to installation.
Use bulbs that do not exceed maximum wattage as marked
on the socket of the light fixture.
Note: The appearance of actual fixtures may vary from
these assembly and installation instructions based on item
number ordered.
Only assemble components as ordered. Do not
substitute or add in additional components.
Wall Mount Assembly Instructions:
1. INSTALLATION PREPARATION
a. Turn off all power to outlet box.
b. Unpack and arrange components to match desired
configuration. Confirm all components are present.
c. Find appropriate threaded holes on Mounting Strap (J).
Assemble the Mounting Screws (K) into the threaded holes so
that they align with the Wall Mount (M). See Figure 1.
J
K
Figure 1
d. Attach Mounting Strap (J) to the outlet box. Align Mounting
Strap so that Mounting Screws (K) are parallel to the ground
(use level if desired).
2. ASSEMBLE SOCKET TO SHADE
a. Unthread and remove the Socket Coupler (A) from the Socket
(B), including wire.
NOTE: Left-Hand thread, turn Clockwise to remove.
b. Feed Socket and Wire through the Socket Gasket (C), Shade
(D), O-Ring (E), Socket Coupler (A), and Arm Gasket (F). See
Figure 2. Screw the Socket Coupler and Socket together in
a counterclockwise direction. Ensure the O-ring is properly
positioned and sits in the groove of the Socket Coupler.
NOTE: If installing Glass Jar Accessory, include Jar
Attachment component(s) (G, H) as provided between the
Socket Gasket and the Shade, as shown in Figure 2.
Figure 2
3. ARM ASSEMBLY
Without Swivel Accessory
a. Feed wire through the Arm (N).
i. When 90° Elbow is used, feed wire up through the
Stem and Arm prior to assembling arms. See Figure 3
NOTE: Discard coupler and threaded ring provided with
the Stem.
Figure 3
b. Apply thread tape (3 turns) or plumbers paste to all
threads on Arm(s).
c. Thread Arm to the Socket Coupler (A). Rotate Shade to
desired position relative to the Arm.
NOTE: Use crescent wrench to fully tighten the assembly.
INSTALLATION AT-A-GLANCE
Step 1: Socket
Step 2: Shade
Step 3: Arm
Step 4: Mount
Note: If installing accessories (glass jar or swivel),
each requires placement within these steps. See
full instructions for details.
TOOLS REQUIRED:
Silicone Sealant • Thread Tape or Plumbers Paste
A – Socket Coupler
B – Socket
C – Socket Gasket
D – Shade
With Swivel Accessory
a. Loosen wing nut and feed wires through the threaded
ends of the Swivel, starting with the external thread.
b. Apply thread tape (3 turns) or plumbers paste to external
thread of swivel and thread to Socket Coupler (A).
c. Feed wire through the Arm (N).
i. When 90° Elbow is used, feed wire up through the Stem
and Arm prior to assembling arms. See Figure 3.
NOTE: Discard coupler and threaded ring provided with
the Stem.
M
d. Apply thread tape (3 turns) or plumbers paste to all
threads on arm(s).
e. Thread Arm to the Swivel, fully tightening to desired
position. Tighten set screw on Swivel to lock in place.
NOTE: Use crescent wrench to fully tighten the assembly.
f. Adjust shade angle, referencing the provided guide
(IS-SVL-US) for maximum shade angles. Tighten wing
nut to lock in place.
4. WALL MOUNTING AND ELECTRICAL INSTALLATION
a. Feed wires through the Mount Gasket (P) and Wall Mount (M)
as shown in Figure 4.
b. Insert Mount Gasket and Arm into the Wall Mount. Align the
Arm relative to the Mount and press the Arm against the Wall
Mount to compress the gasket. Tighten Set Screws (Q) with a
5.0mm or 3/16" Allen wrench.
NOTE: Set screws must have minimum 60 in∙lbs torque
applied.
c. To make wire connections, fixture may be hung to the
Mounting Strap with the provided Tether (R).
d. Trim wires to a minimum length of 6" from the back of Wall
Mount. Strip wire ends to ~ ½".
e. Grounding instructions:
i. Connect outlet box, Mounting Strap and fixture ground
wires with provided wire connector.
CAUTION: Never connect ground wire to black or white
power supply wires.
f. Make wire connections with provided wire connectors.
Reference chart below for connections and wire accordingly.
Connect Line (Black or Red
Supply Wire) to:
*Parallel cord
(Round & Smooth)
Clear without tracer
* Note: When parallel wires (ex. SPT1 or SPT2) are used,
the Neutral wire is square-shaped or ridged and the Line
wire will be a round shape or smooth (see illus.).
Flat Head Screwdriver • Phillips Screwdriver • 5.0 mm or 3/16" Allen Wrench • Crescent Wrench
R
K
H
G
J
E – O-Ring
F – Arm Gasket
G – Jar Attachment
H – Jar Extension
(Use only with Warehouse Shade)
Figure 4
Connect Neutral (White
Supply Wire) to:
Black White
*Parallel cord
(Square & Ridged)
Clear with white tracer
ENG
Neutral Wire
M
P
N
S
Q
J – Mounting Strap
K – Mounting Screws
M – Wall Mount
(optional)
N – Arm
(optional)
g. Carefully position wires, connections and tether into junction
box while aligning fixture Wall Mount holes over Mounting
Strap screws.
h. Secure using Threaded Balls (S) provided.
i. Refine shade position by loosening Wall Mount set screws
and adjusting to preference. Tighten Wall Mount set screws.
j. Use outdoor rated silicone to seal Wall Mount edge
completely around mounting surface to prevent water from
seeping into outlet box.
k. Install applicable lamp.
l. Turn on power.
5. ACCESSORY INSTALLATION (OPTIONAL)
Glass Jar
(Requires Jar Attachment component(s) to be installed in Step
2b, under Assemble Socket to Shade).
a. Glass Jar is compatible with a max A21 sized bulb at the
marked wattage. LED bulbs must be rated for use in an
enclosed fixture.
b. To install glass, raise glass up to the Jar Attachment. Glass
neck will fully insert into the Jar Attachment. Twist glass
counterclockwise, until the glass steps down. To remove
glass, push up on glass and turn clockwise until it releases.
Glass Jar Guard
(Requires Jar Attachment component(s) to be installed in Step 2b,
under Assemble Socket to Shade).
a. Position Guard over glass and screw to Jar Attachment. Twist
counterclockwise until secure.
Wire Cage
a. Disassemble knob and nut on wire cage, allowing the top ring
to relax.
b. Position wire cage over the shade such that the top ring of
the wire cage rest on the lip of the shade.
c. Pressing the tightening plates together, reassemble the knob
and nut, fully securing to the shade.
SPAN FR
Hilo Neutral Fil Neutre
© 2020 Kichler Lighting LLC. All Rights Reserved. | ISWMRLM_LS19012
N
F
A
E
D
C
B
P – Mount Gasket
Q – Set Screws
R – Tether
S – Threaded Ball (x2)