Dedicated Return Line; Connecting Phantom Cleaner To Pool; Installing The Universal Wall Fitting; Assembling And Sizing The Rigid Pressure Hose - Hayward PHANTOM 6000 Guia Del Usuario

Connecting the Phantom Cleaner To Pool
Installing Universal Wall Fitting
Builders: Install the Dedicated Return Line at the
midpoint of the pool's long wall.
S p e c i f i c a t i o n: D e d i c ated Return Line in Pool Wa l l .
D e p t h : At least 6 inches below water level.
S i z e : 1-1/2 inch NPT Female T h r e a d e d .
1 . Flush plumbing lines before proceeding.
2 . Turn Booster Pump and Main Filtration Pump O F F.
3 . Remove plug or existing Universal Wall Fitting from
p r e v i o u s ly installed pool cleaner (if any ) .
4 . Remove the Universal Wall Fitting (part O) and Te fl o n ® t ape
from Bag #1.
5 . When installing or re-installing the Universal Wall Fitting
use Te fl o n ® t ape on its plastic threads. L e ave two starting
threads on the end of the Universal Wall Fitting un-tap e d .
6 . Screw the Universal Wall Fitting into the Dedicated
Return Line.
I m p o r t a n t : Turn the Universal Wall Fitting 1 full turn to the
right to engage starting threads. Be sure both parts are
started properly (not cross threaded) then resume tightening
– hand tighten only. The Universal Wall Fitting may not screw
all the way into the Dedicated Return Line.
Do not over tighten.
Universal Wall Fitting

Dedicated Return Line

Universal Wall Fitting (O)
Te fl o n ® is a registered trademark of E.I. du Pont de Nemours
and Company.
6
Use Only Genuine Hayward Replacement Parts.

Assembling and Sizing the Rigid Pressure Hose

Assembling and Sizing the Rigid Pressure Hose
1 . Open the plastic bag labeled #1 that contains 10 Rigid Hose
Pipes (Part N) and 5 Hose Pipe Couplings (Part I) .
2 . L u b r i c ate the 5 Hose Pipe Couplings by dunking them in
s o apy wat e r.
3 . Align the Barbs on the Hose Pipe Coupling with the Tabs on
the Rigid Hose Pipes and snap together. Be sure the black
o-ring does not slip out of the groove on the Hose Pipe
Coupling (if the o-ring is visible through the latch opening
when pipes are snapped together the o-ring has slipped out
of the groove and will leak)
Connecting Hose Pipes
I N
4 . Make 5 S e t s of Pipe Assemblies by connecting 1 Rigi d
Hose Pipe onto each end of the Hose Pipe Couplings.
Rigid Hose Pipe Assembly
1 Pipe
I
Assembly
N
5 . L o c at e the "Measuring Tap e " (packed in Bag #1), secure the
end of the tape marked " Wall Connector End" on the pool
coping immediat e ly above the Universal Wall Fitting.
6 . Unroll the Measuring Tap e , walk around the pool to the
farthest point along the pool wall from the Universal Wa l l
F i t t i n g .
At the farthest point from the Universal Wall Fitting hold
the Measuring Tape at the pool edge/coping and read the
number of Pipe Assemblies specified on the tap e .
Use Only Genuine Hayward Replacement Parts.
R e c t a n g u l a r-Shaped Po o l
Universal Wall Fitting
(Dedicated Line)
Farthest Point
Kidney-Shaped Po o l
Universal Wall Fitting
(Dedicated Line)
Farthest Point
Angle-Shaped Po o l
Universal Wall Fitting
(Dedicated Line)
Farthest Point
Measuring Ta p e
a . N o t e : If the measuring tape specifies more than 5 Pipe
A s s e m b l i e s , you need to purchase the additional Pipe
sections (P/N AX6000HE) from your Authorized Hay w a r d
D e a l e r.
b . If the measuring tape specifies fewer than 5 Pipe
A s s e m b l i e s , set the remaining Pipe Assemblies aside you
won't need them.
7