DoorBird D10 Serie Manual De Instalación página 6

INSTALLATION
All steps below should be carried out carefully by a competent adult, taking
into consideration any applicable safety regulations. Should you have any
questions, please contact us or a competent specialist directly. Please ensure
that all wires used for the installation are undamaged along their entire
length and approved for this type of use.
Network speed and network components
Please ensure that the upload speed of your Internet connection is at least
0.5 Mbps. You can also carry out a speed test at any time via the DoorBird
app. The user experience is only as good as your network speed, network sta-
bility and quality of your network components, such as your Internet router
and WiFi access points or WiFi repeaters. Please also make sure that your net-
work components are no older than two years old, have been manufactured
by a well-known manufacturer, and have the latest firmware installed.
Should these requirements not be fulfilled, it may happen, for example that
the performance of audio and video is poor or push notifications are delayed
or do not arrive on your smartphone or tablet at all.
High-speed Internet (via landline): DSL, cable or optical fibre
Network: 802.11b/g/n 2.4 GHz or Ethernet, with DHCP
STEP 1: SWITCHING OFF POWER
Switch off the power to all wires leading to the assembly location, i.e. the
door chime, electric door opener, power supply unit for the video door
station etc..
STEP 2: DISMANTLING THE EXISTING DOORBELL
Should there already be a doorbell on the exterior wall of the house, please
dismantle it.
STEP 3: DETERMINING THE ASSEMBLY LOCATION
The video door station uses an ultra wide-angle hemispheric lens so that
even when the person is a minimum distance of 50 cm (19.68 inches) away
from the video door station, a low installation height is sufficient. The lens is
therefore not mechanically adjustable. The camera lens should be located
at an altitude of at least 125 cm (49.22 inches). You may check this prior to
the final mounting. Press the mounting plate against the wall at the desired
installation site and mark the boreholes with a pencil. Remove the mounting
plate again. Ensure that no cables are to be found in the wall behind
the boreholes.
10
Do not expose the device to direct sunlight. The housing temperature
N OTICE
can exceed the maximum allowed temperature limit. This can result
in damage of electric and mechanic components of the device and
injuries especially when touching exterior parts of the device. White
and bright silver-colored front plates absorb less sunlight than dark
ones.
An image sensor must not be exposed to direct sunlight for an
N OTICE
extended period of time. Direct sunlight will "blind" the camera
and may permanently bleach the small color filters on the image
sensor chip.
Any defects caused by direct sunlight is not covered by warranty.
STEP 4: POWER SUPPLY
The video door station can be powered by two simple doorbell wires using
the power-supply unit (mains adaptor) supplied with it or via PoE (Power
over Ethernet) using a network cable. The video door station can alternatively
also be supplied with a DIN-rail power supply unit that you can obtain from
us directly.
The video door station does not use battery power. The use of a mains power
supply permits the transmission and display of on-demand live video at any
time and not only if a visitor has pressed the doorbell.
Power supply using the power-supply unit (mains adaptor)
Two insulated wires are required to power the video door station by plugging
it into the mains. These wires are normally already there and are freely
accessible once you have removed the previous doorbell. Only use the power
supply unit provided along with the video door station, or a DIN-rail power
supply unit that you can obtain from us separately, since this has been spe-
cially stabilized electrically and is equipped with an integrated audio interfe-
rence reduction device. Other power supply units may destroy the video door
station or cause poor transmission quality. The warranty automatically expi-
res if you use a different power supply unit. The power supply unit is plugged
into a wall socket inside your house, usually where the two wires from your
previous doorbell come out of the wall in the interior of the house.
Do not plug the power supply unit into the wall socket yet. Connect the po-
wer supply unit inside the house with the crimp connector provided and the
two wires that you would like to use to power the device.
12