DoorBird D10 Serie Manual De Instalación página 7

Power supply via PoE (as an alternative)
To power the video door station via a PoE switch (e.g. D-Link DGS-1008P) or
PoE injector (e.g. TP-Link TL-PoE150S) in accordance with the PoE standard
IEEE 802.3af Mode A, the four wires bearing the numbers 1, 2, 3 and 6 of a
Cat.5 cable or better are to be used. A Cat.5 cable or better must be used as
network signals can only be transmitted over completely insulated, shielded
and twisted cables. If you use PoE as a source of power, the WiFi interface of
the video door station is automatically inactive, and the four wires for PoE
then simultaneously form the data link. The video door station won't start
if your PoE Switch or PoE injector does not support the PoE Standard IEEE
802.3af Mode A (see Diagnostic-LED and Diagnostic-Sounds).
1. Disconnect the PoE switch or PoE injector from the power grid.
2. Place the network cable in the installation site of the video door station.
Do not combine the power supply from the power supply unit (mains adaptor)
with the power supply via PoE.
STEP 5: FURTHER CONNECTIONS (OPTIONAL)
If desired, connect additional wires to the installation site of the video door
station. The wires or connection options mentioned in this section are optional.
Connecting the unit to a network
You can connect the video door station to your existing
network via WiFi, or alternatively use a network cable
(Ethernet). For reasons of network stability, we principally
recommend using a network cable, as WiFi is sensitive to
interference (range, house walls acting as shields, relia-
bility of performance, third party WiFi networks, wireless
transmitters causing interference in the area, etc.).
The video door station can be powered by PoE or using
the power supply unit provided. If you use PoE as a
source of power, the WiFi interface of the video door
station remains inactive.
Use only four wires (1, 2, 3 and 6) of a network cable that
meets the Cat.5 standard or a better one. The other four
wires of the network cable (4, 5, 7 and 8) are not required.
Connect the network cable in the house to your
Internet router or to your PoE switch or PoE injector
that is connected to your Internet router.
Be sure to use four insulated, shielded and twisted wires
of a network cable in accordance with the Cat.5 standard
or better.
12
Electric door openers
The video door station has a zero-potential relay contact
for a standardised electric door, gate or garage opener
(two wires). There is the possibility of switching on all
electric door openers that work at a maximum power of
1 A in the voltage range of up to 24 V (AC/DC). The video
door station does not provide its own power supply for
the electric door opener. This is provided through the
separate power supply of the electric door opener. You can
learn more about the installation of the power supply
from the instruction manual or technical specifications of
your door opener. Should you have any questions about
this, please contact the manufacturer of your door opener.
You can find compatible electric door opener and a sample
wiring diagram at www.doorbird.com/support
Conventional electric door chime
If someone rings your video door station, you will imme-
diately receive a push notification with sound/vibration
on your smartphone or tablet. In addition the video door
station comes with a zero-potential relay contact for
connecting a conventional electric door chime inside
the building. The relay contact can be used to activate
Be sure to use
the separate operating voltage of the door chime or the
four insulated,
door chime via its trigger input. If the operating voltage
shielded and
of the door chime is activated, it should not be greater
twisted wires of
than 24 V (AC/DC). The power consumption should not
a network cable
exceed 1A. The video door station does not provide its
in accordance
own power supply for the door chime. This is provided
with the Cat.5
through the separate power supply of your conventional
standard or
door chime. Should you have any questions, please con-
better.
tact the manufacturer of your door chime. You can find
6 (R-)
compatible door chimes and a sample wiring diagram at
3 (R+) www.doorbird.com/support
2 (T-)
Conventional door opener button
1 (T+)
If an electric door opener is connected to the video door
station, the door opener can be opened by App and also
be directly controlled via a zero-potential button to be
found in the interior of the building, i.e. a door opening
button. In addition, the door opener button is to be
connected to the connection terminal provided. Please
make sure to add no extra voltage on that contact. You
can find compatible door opener buttons and a sample
wiring diagram on www.doorbird.com/support
Two insulated
wires.
Two insulated
wires.
Two insulated
wires.
13