Tabla de contenido
Publicidad
Wear protective gloves during work. Sharp burrs de-
u
velop on the cut sheets; these can cause injury.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for cutting sheet metal without
deforming the material and is suitable for straight cuts, cut-
outs and narrow curves.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
a)
(1) Battery
a)
(2) Battery release button
(3) On/off switch
(4) Die holder screw
(5) Handle (insulated gripping surface)
(6) O-ring
(7) Die holder
(8) Punch
(9) Die
(10) Rubber ring for knurled screw
(11) Knurled screw for die
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Bosch Power Tools
Technical data
Nibbler
Article number
Rated voltage
No-load stroke rate n
0
Max. steel sheet cutting ca-
A)
pacity
Cutting width
Smallest curve radius
Weight according to
EPTA-Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
C)
ure during operation
and
during storage
Recommended batteries
Recommended chargers
A) with reference to steel sheet of up to 400 N/mm
B) Depends on battery in use
C) Limited performance at temperatures <0 °C
Noise/Vibration Information
Noise emission values determined according to
EN 62841‑2‑8.
Typically, the A-weighted noise levels of the power tool are:
Sound pressure level 87 dB(A); sound power level
98 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 62841‑2‑8:
2
2
a
= 5 m/s
, K = 1.5 m/s
.
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
English | 11
GNA 18V-16
3 601 E29 5..
V=
18
-1
min
1400
mm
1.6
mm
5
mm
40
B)
kg
2.0–3.0
°C
0 to +35
°C
−20 to +50
GBA 18V...
ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
2
1 609 92A 6DR | (31.03.2021)
Publicidad
Tabla de contenido
