Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
14 | English
Additional safety information
Do not touch grinding discs until they have cooled
u
down. The discs can become very hot while working.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
This power tool is not suitable for bench-mounted use.
u
It must not be clamped into a vice or fastened to a work-
bench, for example.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for grinding and deburring metal
with corundum grinding tools, as well as for working with
sanding belt tools.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Collet
(2) Clamping nut
(3) Grinding spindle
(4) Spindle collar (insulated gripping surface)
(5) On/off switch
a)
(6) Battery release button
a)
(7) Rechargeable battery
(8) Handle (insulated gripping surface)
1 609 92A 6YL | (02.12.2021)
(9) Open-ended spanner on the grinding spindle
(10) Open-ended spanner on the clamping nut
(11) Inner shank dimension L
0
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Straight grinder
Article number
Rated voltage
A)
Rated speed
Max. collet diameter
Spanner flat on the
– Clamping nut
– Grinding spindle
Grinding tool diameter, max.
Weight according to EPTA-Pro-
B)
cedure 01:2014
Recommended ambient temper-
ature during charging
Permitted ambient temperature
C)
during operation
and during
storage
Recommended rechargeable
batteries
Recommended chargers
A) Rated no-load speed for the selection of appropriate grinding
tools in accordance with EN 60745. The actual speed is lower
for safety reasons.
B) Depends on battery in use
C) Limited performance at temperatures < 0 °C
Technical data determined with rechargeable battery ProCORE18V
8.0Ah.
Noise/Vibration Information
Noise emission values determined according
to EN 60745-2-23.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 75 dB(A); Sound power level
86 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Total vibration values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745-2-23:
Surface grinding (roughing with grinding tool diameter of
25 mm):
2
2
a
= 3.3 m/s
, K = 1.5 m/s
h
Surface grinding (roughing with grinding tool diameter of
50 mm):
2
2
a
= 11.0 m/s
, K = 1.5 m/s
h
a)
a)
GGS 18V-20
3 601 JB5 4..
V=
18
-1
min
24,000
mm
8
mm
19
mm
19
mm
50
kg
1.5–2.5
°C
0 to +35
°C
–20 to +50
GBA 18V...
ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
Bosch Power Tools
Publicidad
Tabla de contenido
