Tabla de contenido
Publicidad
The cut is made as the punch moves downwards. Guide the
power tool evenly, pushing it gently in the cutting direction.
Applying too much pressure to the power tool will signific-
antly reduce the service life of application tools and can
damage the power tool.
The power tool operates more quietly when it is raised
slightly during cutting. If the punch jams during cutting,
switch the power tool off, lubricate the punch and release
the sheet. Do not use force to do this, as this will damage the
punch and the die.
Maximum steel sheet cutting capacity
The maximum steel sheet cutting capacity d
the strength properties of the material to be cut.
The power tool allows for cutting of metal sheet to the follow-
ing thicknesses:
Material
max. strength
(N/mm
Steel
400
600
800
Aluminium
200
Lubricating/cooling the punch
To extend the service life of the punch (8), a lubricating
agent with good cooling properties (e.g. cutting oil) should
be used.
Apply a line of lubricant to the top side of the metal sheet
along the intended cutting line.
Cutting along a cutting mark or with a guide
Straight cuts are carried out easier when the power tool is
guided alongside a rule.
Contours can be cut by guiding the power tool along a tem-
plate.
For inside cuts, a hole with a diameter of 21 mm must be
pre-drilled.
Temperature Dependent Overload Protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or the battery tem-
perature is outside the permitted range, the stroke rate is re-
duced or the power tool shuts down. When the stroke rate is
reduced, the power tool will not run at the full stroke rate
again until the battery temperature is back within the permit-
ted range. In the event of automatic shutdown, switch off the
power tool and allow the battery to cool down before switch-
ing the tool on again.
Recommendations for Optimal Handling of the Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Bosch Power Tools
depends on
max
d
max
2
)
(mm)
1.6
1.0
0.7
2.0
Follow the instructions on correct disposal.
Maintenance and Service
Maintenance and Cleaning
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
Clean and lubricate the punch (8) and die (9) every three
operating hours.
Change the punch and die in good time when worn. Only
sharp tools produce a good cutting quality and make the
power tool last longer.
The punch (8) and the die (9) may not be resharpened.
Changing the die
Unscrew the knurled screw (11) from the die holder (7).
Take out the die (9).
If necessary, clean the die holder (7). Put a new, well
greased die (9) into the die holder. Pay attention to the
alignment of the flat side.
Screw back on the knurled screw (11) with the rubber
ring (10) attached. Use a hex key to tighten the screw
against the resistance of the rubber ring (3–4 Nm).
Changing the punch
Loosen the die holder screw (4) and pull the die holder (7)
completely out of the housing.
Slide the punch (8) sideways out of the mounting and pull it
out in a downward motion.
Put a new, well greased punch (8) in the groove of the
mounting and centre it.
Push the die holder (7) carefully over the punch and back
into the housing. Turn the die holder into one of the three
possible positions depending on the cutting direction re-
quired. Firmly tighten the die holder screw (4).
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
English | 13
1 609 92A 6DR | (31.03.2021)
Publicidad
Tabla de contenido
