Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
14 | English
Material
max. strength
(N/mm
600
800
Aluminium
200
Adjusting cutter clearance "a"
The cutter clearance a (gap between the
cutters) depends on the sheet thickness
d
to be cut.
max
The clearance a between the cutters should be 10 % of the
maximum sheet thickness (e.g. 0.1 mm cutter clearance for
1 mm sheet thickness).
For softer or more ductile materials, the clearance a must be
decreased; for harder or more brittle materials, it must be in-
creased.
Loosen the fastening screw (10) for the bottom cutter. Ad-
just the requested cutter clearance a with the set screw (9)
for the bottom cutter. The upper cutter (7) and the bottom
cutter (8) may not touch each other.
Check the clearance with a commercially available setting
gauge. Retighten the fastening screw (10) for the bottom
cutter with a tightening torque of 3–4 Nm.
Temperature Dependent Overload Protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or the battery tem-
perature is outside the permitted range, the stroke rate is re-
duced or the power tool shuts down. When the stroke rate is
reduced, the power tool will not run at the full stroke rate
again until the battery temperature is back within the permit-
ted range. In the event of automatic shutdown, switch off the
power tool and allow the battery to cool down before switch-
ing the tool on again.
Maintenance and Service
Maintenance and Cleaning
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
Changing the cutter (see figure A)
The upper cutter (7) and the bottom cutter (8) are identical,
have four cutting edges each, and can be exchanged with
each other.
Turn or replace the cutters in good time. Only sharp applica-
tion tools achieve good cutting capacity and make the power
tool last longer.
1 609 92A 7XM | (26.07.2022)
d
max
2
)
(mm)
1.2
0.7
2.2
To replace the upper cutter (7) loosen the fastening
screw (6), to replace the bottom cutter (8) loosen the
fastening screw (10).
Turn the cutter by 90° or install a new cutter. When installing
the bottom cutter (8), ensure that it fits against the set
screw (9).
Note: Turn the cutter only in the direction indicated in the
figure A and only insert a new cutter in the position shown in
the figure. Cutting is not possible with an incorrectly inser-
ted cutter.
Retighten the fastening screw (6) for the upper cutter and
the fastening screw (10) for the bottom cutter with a tight-
ening torque of 3–4 Nm. Check the cutter clearance a as de-
scribed above.
Upper cutter (7) and bottom cutter (8) may not be re-
ground.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Transport
The recommended lithium-ion batteries are subject to legis-
lation on the transport of dangerous goods. The user can
transport the batteries by road without further require-
ments.
When shipping by third parties (e.g.: by air transport or for-
warding agency), special requirements on packaging and la-
belling must be observed. For preparation of the item being
shipped, consulting an expert for hazardous material is re-
quired.
Dispatch battery packs only when the housing is undam-
aged. Tape or mask off open contacts and pack up the bat-
tery in such a manner that it cannot move around in the
Bosch Power Tools
Publicidad
Tabla de contenido
