Usb Operation - Sharp HT-SBW460 Manual Del Usuario

2. Activate your Bluetooth device and select the search mode. "HT-
SBW460" will appear on your Bluetooth device list.
If you cannot nd the unit, press and hold the button on the remote
control or button on the unit to be searchable. The display will show
"PAIR" and you will hear "Pairing" from the unit.
3. Select "HT-SBW460" in the pairing list. After successful pairing, you will
hear "Paired" from the unit, and the display panel shows "BT".
4. Play music from the connected Bluetooth device.
To disconnect the Bluetooth function, you can:
Switch to another function on the unit.
Disable the function from your Bluetooth device.The Bluetooth device
will be disconnected from the unit after the "Disconnected" voice
prompt.
Press and hold the button on the remote control or
unit.
TIPS:
• Enter "0000" for the password if necessary.
• If no other Bluetooth device pairs with this player within two minutes,
the player will recover its previous connection.
• The player will also be disconnected when your device is moved beyond
the operational range.
• If you want to reconnect your device to this player, place it within the
operational range.
• I f the device is moved beyond the operational range, when it is brought
back, please check if the device is still connected to the player.
• If the connection is lost, follow the instructions above to pair your device
to the player again.
Listen to Music from Bluetooth Device
If the connected Bluetooth device supports Advanced Audio Distri-
bution Pro le (A2DP), you can listen to the music stored on the device
through the player.
If the device also supports Audio Video Remote Control Pro le (AVRCP),
you can use the player's remote control to play music stored on the
device.
1. Pair your device with the player.
2. Play music via your device (if it supports A2DP).
3. Use supplied remote control to control play (if it supports AVRCP).
To pause/resume play, press the
on the unit.
To skip to a track, press the

USB Operation

1. Insert the USB device.
2. Press the
button repeatedly on the unit or press the
the remote control to select USB mode.
3. During playback:
button on the
button on the remote control or
/ buttons on the remote control.
button on
To pause or resume play, press the
on the unit.
To skip to the previous/next le, press the
remote control.
TIPS:
• USB devices up to 32GB are supported.
• Only MP3 les can be played back.
Troubleshooting
No power
• Ensure that the AC cord of the soundbar and subwoofer are correctl
connected.
• Ensure that there is power at the AC outlet.
• Press (standby) button to turn the unit on.
Remote control does not work
• Before you press any playback control button, rst select the correct
source.
• Reduce the distance between the remote control and the unit.
• Insert the battery with its polarities (+/-) aligned as indicated.
• Replace the battery.
• Aim the remote control directly at the sensor on the front of the unit.
No sound
• Make sure that the unit is not muted. Press MUTE or VOL+/VOL– button
to resume normal listening.
• Press button on the unit or on the remote control to switch the soundbar
to standby mode. Then press the button again to switch the soundbar
on.
• Unplug both the soundbar and the subwoofer from the mains socket,
then plug them again. Switch on the soundbar.
• Ensure the audio setting of the input source (e.g. TV, game console, DVD
player, etc.) is set to PCM or Dolby Digital mode while using digital (e.g.
HDMI, OPTICAL, COAXIAL) connection.
• The subwoofer is out of range, please move the subwoofer closer to the
soundbar. Make sure the subwoofer is within 5 m of the soundbar (the
closer the better).
• The soundbar may have lost connection with the subwoofer. Re-pair
the units by following the steps on the section "Pairing the Wireless
Subwoofer with the Soundbar".
• The unit may not be able to decode all digital audio formats from the
input source. In this case, the unit will mute. This is NOT a defect.device
is not muted.
TV has display problem while viewing HDR content from HDMI source.
• Some 4K HDR TVs require the HDMI input or picture settings to be set for
HDR content reception. For further setup details on HDR display, please
refer to the instruction manual of your TV.
I can't fi nd the Bluetooth name of this unit on my Bluetooth device for
Bluetooth pairing
• Ensure the Bluetooth function is activated on your Bluetooth device.
• Ensure you have paired the unit with your Bluetooth device.
This is a 15 mins power off function (ERPII standard requirement for
saving power)
• When the unit's external input signal level is too low, the unit will be
turned o automatically in 15 minutes. Please increase the volume level
of your external device.
The subwoofer is idle or the indicator of subwoofer does not light up.
• Please unplug power cord from the mains sockect, and plug it in again
after 4 minutes to resent the subwoofer.
EN
button on the remote control or
/ buttons on the