Ubbink Pool Cleaner Manual De Usuario página 24

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 27
V - Installation of the water flow guide device
Firstly, check if the pool filtration is switched off. Take off the top of the pressure valve
of the pool by unscrewing the ring. Then replace it by the water flow guide device delivered
with the appliance. See figure 10.
How to fit the water flow guide device
Fit the opening of the water flow guide device in a way the water flow will not interfere
with the moving of the appliance. Try different positions to see which one is best for your pool.
- Water flow towards the pool side
- Water flow towards the bottom
- Water flow towards the hose to divert it around obstacles such as steps and ladders.
Once the water flow guide device is installed, switch the pool filtration back on.
The hoover will now move over the bottom of the pool to suck up all the dirt on its way.
VI - Troubleshooting
The various characteristics of your pool may require certain adjustments for an optimal functioning.
In case of problems, check the following possibilities:
Is the pool outlet closed? Close it
Is the filter clean? Clean the filter
Is the pre-filter basket of the pump clean? Clean the basket
Is the bottom of the appliance filled with dirt? Remove the dirt.
Is there a leak in the hose? Replace the leaking part
Is the pressure regulator blocked by dirt? Clean it.
When the hoover doesn't move or flutter:
- Check if all mains are closed, except for the one to which the appliance is connected.
- Check if there is any dirt in the pre-filter basket of the pump.
- Check if there is any dirt in the flapper of the appliance.
The fragments can stop the moving of the flapper or limit the water flow.
- Your pump is too weak (the pump must be able to filter 9 m
When the appliance stays on one end of the pool:
- Check the direction of the pressure valve and turn it if necessary.
- Check if the hose is long enough to reach the other end of the pool.
- Check if the hose balance is correct.
When the appliance stays on the pool outlet:
- Check if it is correctly closed.
- Check if there is a drain on the pool outlet.
If the pool outlet sticks above the bottom of the pool, please contact a pool professional.
When the appliance moves slower and when bubbles come out of the pressure valve:
- Find the air leak that causes the pump to lose pressure and repair it.
- Thoroughly check the hose to see if there is no leak.
- Check the connection. This must be completely immersed to prevent any incoming air.
- Examine the cover of the pump basket to see if it is fixed correctly, if it is not burst or if the joint is not broken or missing.
If you need assistance, please contact a pool professional.
When the appliance sucks air or stays on the surface of the water:
- Check if the counterweight bar is correctly fixed (see page 2 for the assembly).
- Check if the automatic pressure regulator is correctly installed and if it is not blocked by any dirt.
Thoroughly check if the water level is 7 cm under the pool edge.
- Thoroughly check if the appliance is working at a speed of 2 to 3 meters per minute.
When the appliance stays in a shallow corner or when it is blocked against the steps:
- Check the direction of the pressure valve and turn it if necessary.
- Check if the automatic pressure regulator is correctly installed and if it is not blocked by any dirt.
- The hose should be long enough to reach the other end of the pool plus one extra meter.
- Check if the hose balance is correct on the shallow side.
- Thoroughly check if the appliance is working at a speed of 2 to 3 meters per minute.
- Thoroughly check if the appliance is working correctly and if the counterweight bar is correctly fixed (see page 2 for the assembly).
CLEANMAGIC-DEF.indd 25
3
of water/hour). In this case, please contact a pool professional.
Figure 10
Pool deck
Eyebal Diverter
Pool wall
Eyeball Fitting
Eyebal
Return
Diverter
line
Lock (retaining) ring
26/01/10 10:12

Publicidad

Tabla de contenido
loading

Tabla de contenido