Publicidad
Idiomas disponibles
Idiomas disponibles
Following quantities for each oven:*
• One Heating Element
• One Locking Power Connection Kit
• One Thermostat Kit
*For quantities of ovens exceeding 10, we suggest providing approximately 20% more of the above quantities of spares as sufficient for
day to day operation. For overseas operation we suggest a minimum of 30% more for spares.
Note: Proper re-drying temperatures depend upon the electrode type and its condition. Contact your electrode
manufacturer for specific instructions involving critical operations. Phoenix International, Inc. does not accept liabil-
ity for damage to electrodes and/or welded products resulting from the use of this table. Temperatures and times
shown are recommended and are not guaranteed to be correct.
Phoenix International, Inc. warrants its products against defects in mate-
rial and workmanship. The company will, at its discretion, repair or
replace any properly installed Phoenix International manufactured prod-
uct which fails under normal operating conditions within one year from
date of receipt. Contact the factory for return authorization before return-
ing the product to Phoenix International freight prepaid. If our inspection
confirms that the product is defective under terms of this warranty, it will
be repaired/ replaced and returned, freight prepaid.
8711 West Port Avenue • Milwaukee, WI 53224 USA • Phone (414) 973-3400 • Fax (414) 973-3275
SUGGESTED SPARE PARTS TYPE 1 OVENS
V.
Guide to Electrode and Flux Stabilization
Air Conditioned Storage
AWS
Before Opening
(Type)
RH=Relative Humidity
Cellulose
70-120ºF
EXX10
(21-49ºC)
EXX11
50% Max. RH
EXX20
Titania
70-120ºF
EXX12
(21-49ºC)
EXX13
50% Max. RH
EXX14
Iron Powder M.S.
70-120ºF
(21-49ºC)
EXX24
50% Max. RH
EXX27
Iron Powder Low Hydrogen
EXX18
EXX28
Low Hydrogen
70-120ºF
EXX15
(21-49ºC)
EXX16
50% Max. RH
Low Hydrogen High Tensile
EXXX15
EXXX16
EXXX18
Stainless
40-120ºF
EXXX-15
(4.5-49ºC)
EXXX-16
60% (+/- 10) Max. RH
Inconnel
40-120ºF
Monel
(4.5-49ºC)
Nickel
60% (+/- 10) Max. RH
Hard-Surfacing
Brasses
40-120ºF (4.5-49ºC)
Bronzes
60% (+/- 10) Max. RH
Granulated or
40-120ºF (4.5-49ºC)
60% (+/- 10) Max. RH
Agglomerated Flux
Flux Cored Wire
EXXT-1
40-120ºF
EXXT-2
(4.5-49ºC)
EXXT-5
60% (+/- 10) Max. RH
EXXT-G
www.phx-international.com • info@phx-international.com
After Exposure to Moisture a Sufficient
DryRod Oven
Amount of Time to Affect Weld Quality
Holding Temperature
After Opening
Recondition Step #1
100-120ºF
Not
(38-49ºC)
Recommended
180-230ºF
100-120ºF
(82-110ºC)
(38-49ºC)
1/2 Hour
180-230ºF
100-120ºF
(82-110ºC)
(38-49ºC)
1/2 Hour
180-220ºF
250-300ºF
(82-104ºC)
(121-149ºC)
1- 1/2 Hour
180-220ºF
250-300ºF
(82-104ºC)
(121-149ºC)
1- 1/2 Hour
180-230ºF
150-200ºF
(82-110ºC)
(66-93ºC)
1/2 Hour
150-200ºF
Not
(66-93ºC)
Recommended
100-200ºF
Contact Manufacturer for Specific
(38-93ºC)
Temperatures
250-300ºF
Contact Manufacturer for Specific
(121-149ºC)
Temperatures
This warranty applies only to Products sold by Phoenix International, Inc.
and specifically excludes installation or de-installation labor, transporta-
tion or equipment of another manufacturer used in conjunction with
Phoenix International products. No other warranty, expressed or implied,
exists beyond this warranty declaration.
Phoenix constantly strives to improve its products and therefore reserves
the right to change design, materials, and specifications without notice.
Rebake Step #2
Not
Recommended
250-300ºF
(121-149ºC)
1 Hour
400-500ºF
(204-260ºC)
1/2 Hour
650-750ºF
(343-399ºC)
1 Hour
500-600ºF
(260-316ºC)
1 Hour
Not
Recommended
Not
Recommended
N5610459B-9
Publicidad
