AEG POWERTOOLS OMNI-MTX Manual Original página 8

APPROVAL
This application head is approved for use on the following
powerbases:
OMNI 12C-PB......................................................... 12 V-
OMNI 18C-PB......................................................... 18 V-
OMNI 300-PB ................................................ 220-240 V ~
TECHNICAL DATA OMNI-MTX
Production code.............................................. 4467 08 03...
...000001-999999
Oscillating angle left/right .................................... 2/2 °
Deltasander no load oscillation frequency ........ 20000 min
Weight according EPTA-Procedure 01/2003 ........ 470 g
Noise/Vibration Information
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Vibration emission value a
h
Sanding
OMNI 12C-PB .................................................. 8.0 m/s
OMNI 18C-PB .................................................. 7.4 m/s
OMNI 300-PB ................................................ 12.8 m/s
Uncertainty K = ................................................ 1.5 m/s
Sawing (Multifunctionhead)
OMNI 12C-PB .................................................. 9.0 m/s
OMNI 18C-PB .................................................. 8.9 m/s
OMNI 300-PB .................................................11.6 m/s
Uncertainty K = ................................................ 1.5 m/s
For technical data and approvals of powerbases for use with
various application heads please refer to the operating
instructions of the used powerbase.
WARNING
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool
with another. It may be used for a preliminary assessment of
exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for
diff erent applications, with diff erent accessories or poorly
maintained, the vibration emission may diff er. This may
signifi cantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should
also take into account the times when the tool is switched
off or when it is running but not actually doing the job. This
may signifi cantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the operator
from the eff ects of vibration such as: maintain the tool and
the accessories, keep the hands warm, organisation of work
patterns.
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Wear ear protectors. Exposure to noise can cause hearing
loss.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
14 ENGLISH
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust
protection mask.
Do not machine any materials that present a danger to
health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls!
-1
Do not switch the device on again while the insertion tool is
stalled, as doing so could trigger a sudden recoil with a high
reactive force. Determine why the insertion tool stalled and
rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
2
• it has pierced through the material to be machined
2
• the power tool is overloaded
2
Do not reach into the machine while it is running.
2
The insertion tool may become hot during use.
2 WARNING! Danger of burns
2
• when changing tools
2
• when setting the device down
2
Chips and splinters must not be removed while the machine
is running.
When working in walls ceiling, or fl oor, take care to avoid
electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft
materials (wood, light building materials for walls). Harder
materials (metals) must fi rst be drilled with a hole
corresponding to the size of the saw blade.
Remove the battery pack before starting any work on the
machine.
Always disconnect the plug from the socket before carrying
out any work on the machine.
SPECIFIED CONDITIONS OF USE
Combined with an AEG OMNIPRO powerbase the
Multifunction head with sander pad is designed
wood, metal and plastics and the Multifunction head with
saw blades is designed for cutting fl ush to a surface in wood
and plastics.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
regulations and the directives 2011/65/EU (RoHs), 2014/30/
EU, 2006/42/EC, and the following harmonized standards
have been used:
EN 60745-1:2009 + A11:2010
EN 60745-2-4:2009 + A11:2011
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:2015
EN 50581:2012
Winnenden, 2017-11-30
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
MAINTENANCE
Use only AEG accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-digit
No. on the label and order the drawing at your local service
agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the machine
(OMNI12C-PB, OMNI 18C-PB).
Always disconnect the plug from the socket
sanding
before carrying out any work on the machine
(OMNI 300-PB).
Please read the instructions carefully before
starting the machine.
Do not dispose of electric tools together with
household waste material.
Electric tools and electronic equipment that
have reached the end of their life must be
collected separately and returned to an
environmentally compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
European Conformity Mark
National mark of conformity Ukraine
EurAsian Conformity Mark.
ENGLISH 15