Polk Audio DSWmicroPRO1000 Manual Del Usario página 9

VOLUME SETTINGS
Blue LED Indicator
Volume Level Long Blinks
40 4
39 3
38 3
37 3
36 3
35 3
34 3
33 3
32 3
31 3
30 3
29 2
28 2
27 2
26 2
25 2
24 2
23 2
22 2
21 2
20 2
19 1
18 1
17 1
16 1
15 1
14 1
13 1
12 1
11 1
10 1
9 0
8 0
7 0
6 0
5 0
4 0
3 0
2 0
1 0
0 (Muted) Blinks Slowly
Short Blinks
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
N/A
Customer Service Hours of Operation: Monday-Friday, 9
TROUBLESHOOTING
No sound coming from subwoofer.
Subwoofer doesn't sound right.
The subwoofer is humming.
Subwoofer has no power.
Remote control doesn't work.
Power LED is red.
Subwoofer won't respond
properly to remote control;
The subwoofer seems "locked up"
TECHNICAL ASSISTANCE AND SERVICE
If, after following these hook up directions, you experience difficulty, please
double-check all wire connections. Should you isolate the problem to the
subwoofer, contact the authorized Polk Audio dealer where you made your
purchase, or call Polk Audio's friendly Customer Service Department at
1-800-377-7655 (calls from US or CAN only), 410-358-3600 9am to 6pm EST,
Monday through Friday.
You may also contact us via email: polkcs@polkaudio.com. For more detailed
hook up information and manual updates, visit: www.polkaudio.com.
Specifications and the white paper can be found on the DSWmicro
webpages. Go to www.polkaudio.com.
POWER RATINGS
Model Shipping Weight
DSWmicro 38.2 lbs
PRO 1000
17.327 kg
DSWmicro 38.2 lbs
PRO 2000
17.327 kg
DSWmicro 48.2 lbs
PRO 3000
21.863 kg
DSWmicro 61.9 lbs
PRO 4000
28.077 kg
If hookup is "SUB OUT" to LFE, check
and make sure your receiver is set to
Subwoofer=YES. If hookup is via
speaker wire, check that the polarity
of the wires is correct.
Adjust volume, low pass filter, phase
and settings. Retry AUTO
PRO
("Room") or press "Reset."
There could be interference from a
cable TV line. Disconnect the cable
TV line from the cable box to see
if the hum stops. A low-level hum
is normal.
Is the AC MAIN switch on?
Check outlet; check fuse after
unplugging the subwoofer. The fuse
is located under the power cord
receptacle. Fuse type and rating is
found near the fuse holder.
Remove the plastic tab to activate
the remote control's battery or try
replacing the battery. Ensure the
IR sensor is not blocked.
Switch AC MAIN to "Off," and unplug
subwoofer for 2 minutes, then plug
back in. Turn AC MAIN "ON"
Switch AC MAIN to "Off," unplug
the subwoofer for 30 seconds,
then plug back in.
Turn AC MAIN "ON"
Power Rating
1200 W
1200 W
1200 W
1200 W
-6 polkcs@polkaudio.com
AM PM EST
PRO
PRO
9