Operation - Makita EM400MP Manual De Empleo Y De Seguridad

• Always wear gloves when handling the cutter blade.
• Always attach the blade cover when the tool is not in use or is
being transported.
• The cutter-blade fastening nut (with spring washer) is a
consumable part. If there appears any wear or deformation on the
spring washer, replace the nut. Ask your local authorized service
center to order it.
NOTICE:
• Be sure to use genuine Makita cutter blade.
Turn the tool upside down so that you can replace the cutter blade
easily.
B
A
1. To remove the old cutter blade, insert the hex wrench (A) through
the hole on the protector cover and gear case.
2. Turn the receive washer (B) until it is locked by the hex wrench
(A).
3. Loosen the hex nut (C) clockwise with the socket wrench and
remove the nut (C), cup (D), clamp washer (E) and old cutter
blade (F).
4. Attach the cutter blade (F) onto the shaft so that the guide of the
receive washer (B) fits in the arbor hole in the cutter blade.
5. Install the clamp washer (E) and cup (D). Tighten the hex nut (C)
counterclockwise with 13 to 23 Nm of tightening torque during
holding the receive washer (B) with hex wrench (A).
6. Remove the hex wrench (A). Make sure that the blade is the left
way up.
Removing and installing a nylon cutting head
B
A
C
D
E
F
C
CAUTION:
Do not touch the cord cutter on the protector. Touching the cord
cutter with bare hands may result in injury.
1. To remove the old nylon cutting head, insert the hex wrench (A)
through the hole on the protector cover and gear case.
2. Turn the receive washer (B) until it is locked by the hex wrench
(A).
3. Turn the old nylon cutting head (C) clockwise to loosen and
remove it.
4. Put a new nylon cutting head (C) onto the shaft. Turn it
counterclockwise during locking the receive washer (B) with the
hex wrench (A). Make sure that it is installed securely.
5. Remove the hex wrench (A).

Operation

WARNING:
• If the cutting tool moves at idle, adjust the idle speed of the
engine down. Otherwise you cannot stop the cutting tool by
throttle off and it may cause serious injury.
• Follow the warnings and precautions in the chapter "Safety
precautions" and the instruction manual of the power unit.
Adjusting the hanger position and shoulder
harness
750 mm
(29-1/2")
WARNING:
Do not use the tool if you cannot adjust the hanger position
and shoulder harness length within the range as illustrated.
Using the tool with improper weight balance may bring the cutting
tool upward and result in personal injury.
When replacing an accessory with another, the weight balance
of the equipment may change. In such case, adjust the hanger
position and shoulder harness length as follows.
To change the hanger position, loosen the fixing screw on the
hanger and then move the hanger (A).
Adjust the hanger position and shoulder harness length so that:
• the hanger positions 750 mm (29-1/2") or higher from the ground,
• the cutting tool positions 100 mm (3-15/16") to 300 mm (11-3/4")
high from the ground and
• the unguarded part of cutting tool is horizontally 750 mm (29-1/2")
or farther away from the hanger.
After adjusting the hanger position, tighten the screw with a wrench
or screwdriver (depending on the power unit) securely.
Using a nylon cutting head
During operation, use the tip of the nylon cutting cord for cut.
As the nylon cutting cord is worn and shortened with the cutting
operation, the operator needs to feed it manually.
To feed the nylon cutting cord, tap the nylon cutting head on the
ground while it rotates around 6,000 min
NOTE:
• If the nylon cutting cord does not feed out, rewind it. Refer to the
chapter "Inspection and maintenance."
7
A
100-300 mm
(3-15/16"-11-3/4")
750 mm
(29-1/2")
.
-1