Teuco 255 Instrucciones De Montaje página 24

Assembly Instructions Art. 255-269-282
AVVERTENZE
The product must be installed exactly as supplied by Teuco,
otherwise claims under warranty will not be accepted.
The installer must observe the assembly instructions, using
only the tools and materials recommended, and the accessories
supplied with the product.
The product must be installed directly on the floor and
against finished walls.
Electrical connections must be carried out in compliance with
safety regulations governing bathroom installations,
as described in the accompanying installation standards
manual.
Always use NEUTRAL pH (NON ACETIC) SILICONE.
All fasteners (bags A-B-D) and accessories required for
assembly are contained in the "accessories box".
This manual illustrates the assembly procedure for the
STANDARD version of the product.
This manual constitutes an integral part of the product and
must be kept for future reference.
REMOVING THE BATHTUB PANELS
1
- Undo the screws securing the panels to the bathtub frame.
A
1
- Detach panel 1, followed by panel 2, gripping at the
B
bottom and pulling outwards until the clips release.
PREPARING THE BATHTUB
2
- Position the bathtub in the prepared installation area and
level up, adjusting the outer feet first, then the central
feet, so that all are in contact with the floor.
In order to ensure proper ventilation of the whirlpool
system, when making adjustments leave a minimum
distance of 15mm between the floor and the bottom
edge of the bathtub panel.
WASTE CONNECTION
3
- Make the waste connection using the trap and hose
supplied.
PREPARATORY STEPS FOR ASSEMBLING THE BACK
PANEL
4
- Distance the bathtub from the wall as far as the waste will
allow to make room for the next assembly steps.
FITTING THE SIDE PANEL
5
- Position the side panel on the rim of the bathtub, ensuring
A
the studs locate in the respective sockets.
CAUTION: Apply silicone at the point indicated.
5
- Secure the side panel to the bathtub with the nuts and
B
washers and the two screws and washers.
CAUTION: Apply silicone to the washers as indicated in
the detail.
24
SECURING THE SIDE PANEL AND BACK PANEL
6
- Apply silicone to the side panel and bathtub as shown.
A
6
- Offer the back panel to the studs of the side panel,
B
aligning the studs with an Allen key if necessary.
SECURING AND SILICONING THE BACK PANEL TO
THE BATHTUB
7
- Secure the back panel to the side panel with the nuts and
A
washers.
7
- Secure the back panel to the bathtub with the bolts, nuts
B
and washers.
CAUTION: Apply silicone to the washers as indicated in
the detail, and between the back panel and bathtub.
FITTING THE ROOF
8
- Position the roof on the hydroshower.
A
Insert the hoses 5 and 6 through the holes in the back
panel and connect the hose arrowed in the illustration.
8
- Secure the roof to the back panel and side panel upright
B
with the screws and washers.
- 255-269-282 HYDROSHOWER
9
– PLUMBING CONNECTIONS
C - Hot water connection.
Use a 95 cm stainless steel hose.
F - Cold water connection.
Use a 95 cm stainless steel hose.
5 - Connection of tube 5 for central showerhead with
nebulizer.
- 255-269-282 HYDROSHOWER
WITH EASY MULTIFUNCTIONS
- PLUMBING CONNECTIONS
C - Hot water connection.
Use a 95 cm stainless steel hose.
F - Cold water connection.
Use a 95 cm stainless steel hose.
5-6-Connection of hoses 5 (central showerhead with
nebulizer) and 6 (vertical massage) between roof and
hydroshower.
- 255-269-282
MULTIFUNCTIONS
- ELECTRICAL CONNECTIONS
CA-Electrical connection for whirlpool.
T - Electrical connection for alarm system (only if
bathroom is equipped with alarm system).
A1-Fit the control panel to the rim of the bathtub.
-EQUIPOTENTIAL BONDING
Connect the earth terminal ( ) to the main earth
node for the bathroom.
Connect the yellow-green cable locatred on the back panel
to the heart terminal ( ), feeding it through the hole in the
bathtub.
GB
HYDROSHOWER WITH