Publicidad
Enlaces rápidos
SIDE UNDER SPOILER
PART.No
①
pattern set
⑦
pattern
pattern
ＡＲＨ
pattern
ＣＲＨ
pattern
ＤＲＨ
pattern
ＥＲＨ
E2610VA000
Ft
×１
pattern
ＡＬＨ
ＢＲＨ
pattern
ＣＬＨ
pattern
ＤＬＨ
pattern
ＥＬＨ
10mm
9.5mm
6mm
FUJI HEAVY INDUSTRIES, LTD.
②
③
×２０
⑤
⑥
×２
pattern
pattern
ＢＬＨ
pattern
pattern
＋
3mm
(1)
Applicable : WRX, WRX-STI
(2015MY~)
INSTALLATION INSTRUCTION
GUIDE D'INSTALLATION
EINBAUANLEITUNG
MANUALE D'INSTALLAZIONE
MANUAL DE INSTALACION
④
×２０
×２０
×２
pattern
ＦＲＨ
ＦＬＨ
pattern
ＧＲＨ
ＧＬＨ
pattern
ＨＲＨ
ＨＬＨ
×１
8mm
140219
⊿01
Publicidad
Manuales relacionados para STI E2610VA000
Resumen de contenidos para STI E2610VA000
- Página 1 ⊿01 Applicable : WRX, WRX-STI (2015MY~) SIDE UNDER SPOILER INSTALLATION INSTRUCTION GUIDE D'INSTALLATION EINBAUANLEITUNG MANUALE D'INSTALLAZIONE MANUAL DE INSTALACION PART.No E2610VA000 ② ③ ④ ① ×２０ ×２０ ×２０ ⑤ ⑥ ×１ ×２ ×２ pattern set ⑦ pattern pattern pattern pattern...
- Página 2 ＜CAUTION＞ (1) Perform installation properly according to the procedures indicated in the instruction manual. Improper installation can result in damage to your vehicle or serious injury. (2) Be careful when driving after installing this product as ground clearance at the wheel arch and center section is decreased by approximately 2 cm (0.8 inches) and 1.5 cm (0.6 inches) respectively.
- Página 3 NOTE: Do not wash the vehicle for 24 hours following installation of this product. If this product requires cleaning after installation, wipe with a soft cloth or sponge with mild detergent and wipe thoroughly with a dry cloth. Do not use gasoline, thinner, acid, alkaline or other solvent based products. The recommended adhesive surface temperature range is 77 F - 104 F(25℃...
- Página 4 pattern ⑦ Ｃ pattern ⑦ Ｂ pattern ⑦ Ａ pattern ⑦ Ｄ ＬＨ ＶＬ pattern Ｆ ⑦ pattern ⑦ Ｅ pattern Ｇ ⑦ pattern Ｈ ⑦ Attach pattern sheets ( ) to shown face of OE side sill spoiler, and then mark to the intersection on the pattern sheet. １...
- Página 5 ( The marking point of pattern H ) 3mm→6mm ③ Insert ③ into the 10×φ9.5mm holes. detergent...
- Página 6 Peel 30mm of the tape liner, and seal with tape on the outside of the Side under spoiler. ⑤（Φ１０） ⑥（Φ６） １ ２ ３ ４ ５ ６ ７ ８ ９ ④ ② Tighten the screws temporarily.
- Página 7 １ ２ SEIKQ 4.5 kg 10 sec (10 lbs) １ ２ ３ ４ ５ ６ ７ ８ ９ 1.0±0.5N･m ② （0.8±0.3 lb-ft） Tighten the screws completely. Re-install the OE side sill spoiler by push OE side sill spoiler inward, towards the vehicle, then Re-install the 5×large clips, 2×screw type clips, and 1 button clip.