Briteq LDP POWERBAR 12TC Manual De Instrucciones página 5

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

ENGLISH
 Use DOWN and UP buttons to change the DMX512 address.
 Once the correct address shows on the display, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Channel Mode
 Press the MENU button until
is shown on the display.
 Press the ENTER button so the display starts blinking.
 Use DOWN and UP button to select one from the five DMX mode available on the LDP powerbar.
Please check below the dmx charts of the different DMX modes.
 Once the mode is selected, press the
ENTER button to confirm.
To go back to the main menu without
any change press the MENU button
shortly.
If you want to go back to normal running
mode: press the MENU button for about
2 seconds.
Show Mode
Choose the Show mode when used in
standalone or master/slave mode.
 Press the MENU button until
is showing on the display.
 Press the ENTER button, the display
starts blinking.
 Use DOWN and UP buttons to select
one of the available shows:
(show 1),
(show 2),... up to
(show 16). Press enter to
confirm, then
(fade time) will
blink on the display. Use the up and
down button to adjust the fade time,
then press enter to set the value.
The fade time can be set from 0 to
255.
(wait time) will blink on the
display, use the up and down button
to adjust the wait time, then press
enter to set the value.
The wait time can be set from 0 to
255.
To go back to the main menu without
any change press the MENU button
shortly.
If you want to go back to normal running
mode: press the MENU button for about
2 seconds
BRITEQ
®
OPERATION MANUAL
LDP-POWERBAR 6/12TC
ENGLISH
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for the DMX-
signal.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to standalone
mode.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
(yes blackout) or
 Once the mode has been selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Manual Test
Used to manually test all functions of the unit.
 Press the MENU button to show
on the display.
 Press the ENTER button, the display will show the first parameter (RED)
 Use the DOWN and UP button to select
(Dimmer) or
(Strobe) mode.
 Press the ENTER button, the display will show the current value for the selected parameter.
 Use the DOWN and UP button adjust the value from 0 to 255 to test the unit.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Adjust White balance
Makes it possible to adjust the white color when all colors are at maximum.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display will show the first color (RED)
 Use the DOWN and UP button to select the
 Press the ENTER button, the display will show the last value selected.
 Use the DOWN and UP button to adjust the value from 125 to 255 and press ENTER to confirm.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Self Test
Used to activate the internal "self-test" program that runs continuously.
Press the MENU button until the display shows
 Press the ENTER button to start the internal self-test program.
 The unit will run continuously in sequence the RED, GREEN, BLUE and WHITE color
 This self test allow the user to check if every LEDs are working perfectly.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Led Display
Display on: display is always on.
Display off: display is off when not used.
 Press the MENU button until the display shows
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select
(display always on) or
 Once the mode has been selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
BRITEQ
®
OPERATION MANUAL
(no blackout) mode.
(Red),
(Green),
(Blue),
(White),
(Red) or
(Green) or
(Blue) color.
.
.
(display off when not used).
LDP-POWERBAR 6/12TC

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ldp powerbar 6tc

Tabla de contenido