Bixolon SRP-330 Guia De Instalacion

KN04-00059A (Rev.1.2)
◈ Information
This Installation Guide includes a brief outline of information necessary for product
installation. For more detailed installation information, please refer to the user manual in the
enclosed CD. The contents of the CD include the following.
1. Manual: User Manual, Code Chart, Control Commands
2. Drivers: Windows Drivers, OPOS Drivers
3. Utilities: a Logo download tool and a virtual memory switch control tool
We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality
of all our products. In following, product specifications and/or user manual content may be
changed without prior notice.
◈ Components
SRP-330
2" Partition USB A- B Cable
◈ Connecting the cables
1. Turn off the printer and the host ECR (host computer).
2. Plug the power cord into the Adaptor, and then plug the Adaptor into the power connector
of the printer.
3. Check the interface cable (Serial, Parallel, USB, or Ethernet), and connect the interface
connector cable accordingly.
4. Plug the drawer kick-out cable into the drawer kick-out connector on the printer.
※ Do not use an adapter that was not supplied with the printer.
Drawer kick-out connector
Interface connector
Interface cable
(Serial/Parallel/USB/Ethernet)
◈ Installing the Paper Roll
◈ Using the Operation Panel
• POWER (LED)
When turning on the power, a blue LED will be lit.
• ERROR (LED)
When an error occurs, a red LED will be lit.
(e.g. no paper, cover ajar, etc.)
• PAPER (LED)
Red LED will be lit when the paper roll is running low. The LED blinks
when the printer is in self-test standby mode or macro execution standby
mode.
• FEED (Button)
Press the FEED button once to discharge extra paper. Holding down the
FEED button will discharge paper continuously until the button is
released.
Cable cover
Procuct Installation CD Procuct Installation CD Procuct Installation CD
CD Installation Guide
AC/DC Adaptor
Power connector
Adaptor
Drawer kick-
out cable
1. Open the paper roll cover by raise the cover-open
lever.
2. Insert a new paper roll, making sure to align it
properly.
3. Pull out a small amount of paper, and close the
cover.
※ Note
When closing the cover, press down on the center
of the cover to ensure that the paper is in contact
with the roller.
Printing quality may not be optimum if
recommended paper is not used. (Refer to the
User's Manual.)
Printer Installation Guide
THERMAL PRINTER SRP-330
◈ Mounting 2" Partition
Hang the partition at the front and press down the rear to mount the 2" partition as shown in
the picture.
※ Caution
After using 2"(58mm) paper roll, do not replace it with 3"(80mm) paper roll.
◈ Setting the DIP Switches
Changing Dip Switch settings must be done when the printer is off. Any changes done while
the printer is on will not be processed.
Paper Roll
1. Serial Interface
• DIP Switch 1
SW
1-1 Auto cutter control
1-2 Flow Control
1-3 Data Length
1-4 Parity Check
1-5 Parity Selection
1-6
1-7 Baud Rate Selection (bps)
Power cord
1-8
• Table 1 – Baud rate (bps) Selection
Transmission Speed
2400
4800
9600
19200
38400
57600
115200
2. Parallel / Ethernet Interface
• DIP Switch 1
SW
1-1
1-2
1-3
1-4
1-5
1-6
Power cord
1-7
1-8
◈ Self-Test
1. Make sure the paper roll has been installed properly.
2. Turn on the power while holding down the FEED button. The self-test begins.
3. The self-test prints the current printer status, providing the control ROM version and the
DIP switch setting.
4. After printing the current printer status, self-test printing will print the following, and
pause. (The PAPER LED light blinks.).
5. Press the FEED button to continue printing. The printer prints a pattern using the built-in
character set.
6. The self-test automatically ends and cuts the paper after printing the following.
7. After the self-test is complete, the printer returns to normal on-line status.
※ Note
The self-test lets you know if your printer is operating properly. It checks the print quality,
ROM version, and DIP switch settings.
Function ON
Disable
XON/XOFF
7bits
Yes
EVEN
Refer to the following table 1
1-6
ON
ON
OFF
OFF
OFF
OFF
ON
Function ON
Auto cutter control Disable
Reserved -
Reserved -
Reserved -
Reserved -
Reserved -
Reserved -
Reserved -
SELF-TEST PRINTING.
PLEASE PRESS THE FEED BUTTON.
*** COMPLETED ***
OFF Default
Enable OFF
DTR/DSR OFF
8bits OFF
No OFF
ODD OFF
OFF
ON
OFF
1-7 1-8 Default
OFF OFF
OFF ON
ON OFF
OFF OFF 9600
ON ON
OFF ON
ON ON
OFF Default
Enable OFF
- OFF
- OFF
- OFF
- OFF
- OFF
- ON
- OFF