Bixolon SRP-370 Guia De Instalacion

KN04-00017A (Rev.2.7)
◈ Information
This Installation Guide includes a brief outline of information necessary for product
installation. For more detailed installation information, please refer to the user manual in the
enclosed CD. The contents of the CD include the following.
1. Manual: User Manual, Code Chart, Control Commands
2. Drivers: Windows Drivers, OPOS Drivers
3. Utilities: a logo download tool and a virtual memory switch control tool
We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality
of all our products. In following, product specifications and/or user manual content may be
changed without prior notice.
◈ Components
Cable Cover
SRP-370/372
AC/DC Adaptor
◈ Connecting the cables
1. Turn off the printer and the host ECR (host computer).
2. Plug the power cord into the Adaptor, and then plug the Adaptor into the power connector
of the printer.
3. Check the interface cable (Serial, Parallel, USB, or Ethernet), and connect the interface
connector cable accordingly.
4. Plug the drawer kick-out cable into the drawer kick-out connector on the printer.
※ Do not use an adapter that was not supplied with the printer.
Drawer kick-out connector
Power connector
Adaptor
Power cord
◈ Installing the Paper Roll
※ Note : Adjusting the Paper Near-End Sensor
The paper near-end sensor performs the two functions of gauging
'No Paper' status as well as detecting black marks. In order to
gauge 'No Paper' status, the sensor must be in the "a" position as
shown in the picture. The factory default setting places the
sensor in this position. To detect black marks, the sensor must
be in the "b" position.
Black marks must have an optical density (O.D.) of at least 0.6 to
be safely detected.
As the black mark density of the paper can cause operating
errors, make sure to check it.
※ Note: O.D. Value Chart
1.4
All manuals and user guides at all-guides.com
Procuct Installation CD Procuct Installation CD Procuct Installation CD
Paper Roll CD
Power cord Installation Guide
Interface
connector
Drawer Interface cable
(Serial/Parallel/USB/Ethernet
kick-out
cable
1. Open the paper roll cover by
pressing the cover-open button.
2. Insert a new paper roll, making
sure to align it properly.
3. Pull out a small amount of paper,
and close the cover.
※ Note
When closing the cover, press down
on the center of the cover to ensure
that the paper is in contact with the
roller.
Printing quality may not be optimum
if recommended paper is not used.
(Refer to the User's Manual.)
0.9 0.6 0.3 0.2
Printer Installation Guide
THERMAL PRINTER
◈ Using the Operation Panel
• POWER (LED)
When turning on the power, a green LED will be lit.
• ERROR (LED)
When an error occurs, a red LED will be lit.
(e.g. no paper, cover ajar, etc.)
• PAPER (LED)
Red LED will be lit when the paper roll is running low. The LED blinks
when the printer is in self-test printing standby mode or macro execution
standby mode.
• FEED (Button)
Press the FEED button once to discharge extra paper. Holding down the
FEED button will discharge paper continuously until the button is
released.
◈ Setting the DIP switches
Changing Dip Switch settings must be done when the printer is off. Any changes done while
the printer is on will not be processed.
1. Serial Interface
• DIP Switch 1
SW Function
1-1
Baud Rate Selection
1-2
1-3 Handshaking
1-4 Reserved
1-5 Auto Cutter
1-6 Paper
1-7 Reserved
1-8 Reserved
• DIP Switch 2
SW Function
2-1
2-2 Print Density
2-3
2-4 Historical Control
2-5 Reserved
Interface Condition
2-6
Selection
2-7 Near End Sensor Status
2-8 Printing Width
2. Parallel / USB Interface
• DIP Switch 2
SW Function
2-1
2-2 Print Density
2-3
2-4 Historical Control
2-5 Reserved
Interface Condition
2-6
Selection
2-7 Near End Sensor Status
2-8 Printing Width
• Table1 – Baud rate (bps) Selection
1-1
OFF
ON
OFF
ON
• Table 2 – Print Density Selection
2-1 2-2
ON ON
OFF ON
ON OFF
OFF OFF
OFF OFF
ON OFF
OFF ON
ON ON
SRP-370/372
ON OFF
Refer to the following table 1
Software Hardware
(Xon/Xoff) (DTR/DSR)
--
Disable Enable
Two colors Mono color
--
--
ON OFF
Refer to the following table 2
Enable Disable
--
Memory
DIP Switch
Switch
Disable Enable
2" Printing 3" Printing
ON OFF
Refer to the following table 2
Enable Disable
--
Memory
DIP Switch
Switch
Disable Enable
2" Printing 3" Printing
1-2 Transmission Speed
OFF 9600
OFF 19200
ON 38400
ON 115200
2-3 Print Density
ON 130%
ON 120%
ON 110%
ON 105%
OFF 100%
OFF 95%
OFF 90%
OFF 80%
Ver.2
Default
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
Default
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Default
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Default
115200
Default
100%