Touch Control Panel - Ariston AQUALTIS AQD1070D 497 X Instrucciones Para La Instalación Y El Uso

Ocultar thumbs Ver también para AQUALTIS AQD1070D 497 X:
Tabla de contenido

Publicidad

Touch control panel

WASH CYCLE
SELECTOR
knob
ON/OFF
Button with
indicator light
Button with
ON/OFF indicator light: press this briefly to switch
the machine on or off. The green indicator light indicates that the
machine is switched on. To switch off the Washer-dryer during
the wash cycle, press and hold the button for approximately
3 seconds; if the button is pressed briefly or accidentally the
machine will not switch off. If the machine is switched off during a
wash cycle, this wash cycle will be cancelled.
WASH CYCLE SELECTOR knob: may be turned in either
direction. To select the most suitable wash cycle, please refer
to the "Table of wash cycles".
The knob will not move during the wash cycle.
M1-M2 buttons: press and hold one of the buttons to store
a cycle with your own set preferences in the memory of
the machine. To recall a previously-stored cycle, press the
corresponding button.
DRYING button
: press to decrease or exclude drying;
the selected drying level or time will appear on the display
(see "How to run a wash cycle or a drying cycle").
button: press to modify or exclude
TEMPERATURE
the temperature setting; the value selected will appear on the
display above (see "How to run a wash cycle or a drying cycle").
SPIN CYCLE
button: press to modify or exclude the spin
cycle; the value selected will appear on the display above (see
"How to run a wash cycle or a drying cycle").
DELAYED START
button: press to set a delayed start for
the selected wash cycle; the set delay time will appear on the
display above (see "How to run a wash cycle or a drying cycle").
OPTION buttons: press to select the available options. The
indicator light corresponding to the selected option will remain
lit (see "How to run a wash cycle or a drying cycle").
WASH CYCLE PHASE icons: these illuminate to indicate
the progress of the wash cycle (Wash
Drain
– Drying
). The text
complete.
START/PAUSE button with indicator light: when the green
indicator light flashes slowly, press the button to start a wash
M1
M2
DISPLAY
DRYING
button
– Rinse
– Spin/
lights up when the cycle is
SPIN
button
TEMPERATURE
button
OPTION
DELAYED START
buttons
button
cycle. Once the cycle has begun the indicator light will remain
lit in a fixed manner. To pause the wash cycle, press the
button again; the indicator light will flash in an orange colour. If
the "LOCK"
indicator light is switched off, the door may be
opened. To start the wash cycle from the point at which it was
interrupted, press the button again.
LOCK
indicator light: indicates that the porthole door is
locked. To open the door, pause the wash cycle (see "How to
run a wash cycle or a drying cycle").
CONTROL PANEL LOCK
activate or deactivate the control panel lock, press and hold
the button for approximately 2 seconds. when the indicator
light is illuminated, the control panel is locked. This means
it is possible to prevent wash cycles from being modified
accidentally, especially where there are children in the home.
ECO indicator light: the
washing parameters, an energy saving of at least 10% is made.
Furthermore, before the machine enters "Standby" mode, the
icon will light up for a few seconds; when the machine is switched
off the estimated energy saving will be around the 80% mark.
CHANGE LANGUAGEsThe first time the machine is
switched on, the first language will flash on the display. The
" ", "OK" and "V" symbols will appear on the display, in line
with the 3 buttons on the right-hand side. The languages
change automatically every 3"; alternatively, they can be
changed by pressing the buttons next to the " " and "V"
symbols. Use the "OK" button to confirm the language, which
will be set after 2". If no buttons are pressed, the automatic
language change will begin again after 30".
To change the language, switch the machine on and off
again; in the 30" time period after it has been switched
off, press and hold the temperature
+delayed
start buttons simultaneously for 5''. A short
sound alert will be emitted and the set language will flash
on the display.
Press the buttons next to the " " and "V"
symbols to change the language. Use the button next to the
"OK" symbol to confirm the language, which will be set after
2". If no buttons are pressed, the language set previously will
be displayed after 30". Switch on the machine.
START/PAUSE
button
with indicator light
ECO
indicator light
CONTROL PANEL LOCK
button with indicator light
LOCK
indicator light
button with indicator light: to
icon lights up when, after altering the
+spin
WASH
EN
CYCLE
PHASE
icons
7 7

Publicidad

Tabla de contenido
loading

Tabla de contenido