Mounting Instruction - Chicago Pneumatic CP80300 Manual De Usuario

EN
English
1. Technical Data (See figure 1.)
Technical Data Lifting capacity
Unit
CP80300
CP80500
Technical Data A
Unit [mm]
CP80300 150
CP80500 150
All values are current as of the date of this publication. For the latest information please visit www.cp.com.
2. Machine type(s)
• An Air-Hydraulic jack is a device to lift a vehicle up to for accessibility during repair and maintenance.No other use permitted. For
professional use only.
• A Jack is only a lifting device and should never be used for transporting and/or loading a vehicle. Lifting a vehicle with person inside is
prohibited. Moving the jack with load is prohibited.
• Please read the instructions carefully before starting the machine.

3. Mounting instruction

WARNING
Make sure every parts are fixed and tightened.
• First loosen the screw attached to the side of the wheels,CP80300,of the frame, CP80500,Fig. 02.
• Insert the complete handle into the opening of the lever support, Fig. 03.
• Connect the hose and the spring to the lifting device .The white hose is connected under the black hose. Fig. 04.
• Screw back the wheels, Fig.05.
• Observe the correct positioning (pin of the lever in the hole of the lever support), Fig.06.
Caution
Working area of 1 m must be kept free both in front of and behind the machine while it is in operation so that it is always
easily accessible.
Purge air from the hydraulic system:
• Push the trigger right, "Up" position and fully raise up the piston.
• loosen a little the screw in the saddle Fig.08.
• Let the pump run for approx. 10 seconds, and tight the screw FIG.08 and push the trigger left, "Down" position.
• repeat the operation 3 times to eliminate the air in the system.
Scale: 1:1 Document Ref: 8940169914_REV: 01 _ 05-2012
4. Operation
• Verify the control lever is in the neutral position.
• Connect the shop air supply to the jack. Rated air pressure is 10bar. Install an air filter/lubricator in the shop air line, because water in the air
line will damage the jack.
• Move the control lever to UP to raise the saddle to the contact point. Move the control lever to neutral position.
• Check the placement of the jack. The load must be centered on the jack saddle. Avoid jack wheel obstructions such as gravel, tools, or
uneven expansion joints.
• Move the control lever to UP finish lifting the vehicle.
• Immediately place approved support stands under the vehicle's lifting points (recommended by the vehicle manufacturer).
• To lower the load, Push the trigger left, "Down" position.
WARNING
Brake vehicle. Chock vehicle tires that are still in contact with the ground.
WARNING
SLOWLY and CAREFULLY lower the vehicle onto the support stands by pushing the control lever to the DOWN position.
WARNING
It is not allowed to work under the raised load until it is secured by suitable means.
WARNING
The operator shall be provided with all necessary information about training and about pumping and translating forces.
Pressure Air Consumtion
[kg] [bar] [l/min]
30000 7-10
50000 7-10
B C D E
[mm] [mm] [mm] [mm]
205 290 360 105
250 315 430 125
Stroke Length of spindle
[mm]
200 145 150-295
250 210 150-360
F G
[mm] [mm] [Ømm]
225(30T)-295(15T) 1355 63.5
220(50T)-275(25T)-
1355
360(12T)
CP80300/CP80500
Hydraulicioil Quantity
[mm] [kg]
0.75
1.6
P Weight Adapter 1
[kg] [mm]
47 Ø 68 x 120
91 60 Ø 68 x 120
Air Hydraulic jack
Sound pressure
dB
91
87
Adapter 2
[mm]
Ø 68 x 70
Ø 68 x 70