Programming; Menu Mode - Denon CDR-1000 Instrucciones De Operación

11

PROGRAMMING

You can program up to 99 tracks to play in any desired
sequence.
Tracks can be programmed more than once, but each time
counts as a track ("STEP").
Programming
4 3
B CDR-1000 PLAY /PAUSE STOP REC MODE
PCM AUDIO TECHNOLOGY/ CD RECORDER OPEN /CLOSE
STANDBY REM REC TIME TRACK TIME
/
1 2 3 4 5 6 7 8 9 10 11
L
OPTICAL I CD RW R MANUAL SYNC REPEAT
REMOTE SENSOR
STORE/
PHONES PHONES LEVEL DISPLAY INPUT SHUFFLE MENU
¢ ON / STANDBY £ OFF
-
SCROLL CANCEL / DELETE
ERASE FINALIZE
MIN MAX
ON /STANDBY
SCAN
REPEAT PROGRAM SHUFFLE
1,3
ABC DEF GHI
1 2 3
JKL MN OPQ
2
4 5 6
RST UVW XYZ
7 8 9
TRACK MARK SPACE SCROLL
0
PLAY
4
STOP
3
PAUSE
STORE / CANCEL/
MENU ENTER DELETE
2
REMOTE CONTROL UNIT RC-276
1 In Stop mode press the PROGRAM button to enter
Program mode.
• "PROGRAM" flashes and "PROGRAM" appears on the
display.
2 Select the required track numbers by turning the MULTI
JOG dial left or right and store by pressing the ENTER
button.
or
Button in a track number with the number buttons and
store by pressing the ENTER button. For 2-digit numbers,
press the buttons in rapid succession.
• The track will be stored in the program.
• The track number, total program time and the number
of programmed tracks ("STEP") are displayed.
• Repeat step 2 for all tracks to be programmed.
3 Press the STOP button ( ) or PROGRAM button to end
2
programming.
• "PROGRAM" lights continuously.
4
Press the PLAY button ( ) to start programmed play.
1
NOTES:
• To review the program, press the PROGRAM button
followed by manual search reverse button (
manual search forward button ( ) with the CD
7
recorder in Stop mode.
• To add more tracks to the program, repeat steps 1 to 4.
• If you try to store more than 99 tracks, "PROG FULL"
appears on the display.
• The total program time will not be displayed when it
1,3 exceeds 199 minutes. Neither will the program
remaining time be displayed when the remaining time
of programmed play exceeds 199 minutes.
REC
• Program operations will not be possible during play or
PROGRAM
MULTI JOG pause.
+
ENTER
Clearing a program
2
1
Press the STOP button ( 2 ) if necessary to stop programmed
play.
2 Press the STOP button ( ) again to clear the program.
2
• "PROGRAM" disappears from the display.
• The program is also cleared if you open the disc tray.
Erasing a track from a program
1
In Stop mode press the PROGRAM button to enter
Program mode.
2 Use the manual search reverse button (
manual search forward button ( ) to select the track
7
from which to delete.
• The track number and program step will be shown on
the display.
3 Press the CANCEL/DELETE button to erase the track
from the program.
• The remaining program steps and the remaining
playing time of the program will be displayed.
Intro Scan Play
The first 10 seconds from the beginning of the track can be
listened to in succession for the tracks recorded on the disc.
ON /STANDBY
SCAN
1
REPEAT PROGRAM SHUFFLE
ABC DEF GHI
1 2 3
JKL MN OPQ
1 Press the SCAN button while the unit is stopped.
• The "SCAN" display will light. The time display will
count down from 0 : 0 to 0 : 00.
• Intro Scan play will start from the first track.
Play will stop when all of the recorded tracks have ended.
To listen to a track all the way to the end during Intro Scan
play, press the SCAN button or the PLAY button (
remote control once.
A press of the SCAN button during program setting will
result in Intro Scan play beginning in the order of
programmed tracks.
12

MENU MODE

) or
6
Remarks About Menu Mode
• In Menu mode you will have access to a number of features
which are not available via the regular buttons (on the deck's
front and the remote control).
• The TEXT submenus allow you to give names to discs and
tracks. The disc and track names will be displayed during
playback.
• In the RECORDING submenus you can set Auto Track,
Balance and Fade.
• All settings (except Balance) made in Menu mode will be
stored in the deck's memory and can be called up and
changed at any time.
General Operation
B CDR-1000
PCM AUDIO TECHNOLOGY/ CD RECORDER
STANDBY REM REC TIME TRACK TIME
1 2 3 4 5 6 7 8 9 10 11
L
OPTICAL I R MANUAL SYNC
CD RW
REMOTE SENSOR
PHONES PHONES LEVEL
¢ ON / STANDBY £ OFF
MIN MAX
ON /STANDBY
SCAN
REPEAT PROGRAM SHUFFLE
ABC DEF GHI
1 2 3
JKL MN OPQ
4 5 6
RST UVW XYZ
7 8 9
6 ) or the
TRACK MARK SPACE SCROLL
0
PLAY
STOP
PAUSE
STORE / CANCEL/
MENU ENTER DELETE
1,6
REMOTE CONTROL UNIT RC-276
1 Press the STORE/MENU button to enter Menu mode.
• "TEXT EDIT" appears on the display.
2
Turn the MULTI JOG dial to select the required
submenus.
) on the
1
Menu Structure
2
Turning the MULTI JOG dial clockwise will cause the menu to
change as follows.
Structure of the menu mode while stopped
ª
TEXT EDIT
ª
TEXT ERASE
ª
MEMORY VIEW
ª
SET FADE
7
ª
AUTO TRACK
OPEN /CLOSE PLAY /PAUSE STOP REC MODE REC
/
REPEAT PROGRAM
STORE/
DISPLAY INPUT SHUFFLE MENU MULTI JOG
- +
CANCEL / DELETE
SCROLL ERASE FINALIZE
ENTER
Structure of the menu mode while recording is paused
1,6 2~5
ª
AUTO TRACK
ª
SET BALANCE
ª
7
SET FADE
3
3
Press the ENTER button to confirm selections.
4
Turn the MULTI JOG dial to select options in the
submenus.
5
Press the ENTER button to confirm selections.
6 Press the STORE/MENU button to store settings and
return to the submenu.
7 Press the STOP button (
Menu mode.
NOTES:
• Text can only be edited for unfinalized discs.
(Finalized CD-RW discs must be unfinalized first.)
• The Auto track recording setting mode is not displayed
in the auto start recording mode.
ENGLISH
Text edit mode
Text erase mode
Text memory review
mode
Fade recording setting
mode
Auto track recording
setting mode
Auto track recording
setting mode
Recording balance
setting mode
Fade recording mode
) to store settings and exit
2
15