Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
10 • ENGLISH
•
Figure F - Empty the dust from the bowl ( 3 ).
•
To replace dust bowl, place it back onto the handle
until it "clicks" firmly into position.
For a more thorough cleaning, remove bowl as
described below.
For a more thorough cleaning (Fig. G, H)
•
Figure G - Press the dust bowl release button ( 2 ) on
the handle and remove the dust bowl.
•
Remove filter from within the bowl.
•
Shake or lightly brush any loose dust off filter.
•
The dust bowl ( 3 ) and filter can be washed in warm
soapy water. Allow to dry before placing back into
the vac.
•
Place filter back into the bowl pressing firmly to
ensure a secure fit.
•
To replace dust bowl, place it back onto the handle
until it "clicks" firmly into position.
IMPORTANT: Maximum dust collection will only be
obtained with a clean filter and an empty dust bowl. If dust
begins to fall back out of the product after it is switched off,
this indicates that the bowl is full and requires emptying.
•
Wash the filters regularly using warm, soapy water
and ensure that it is completely dry before using
again. The cleaner the filter is, the better the product
will perform.
•
It is very important that the filter is correctly in position
before use.
NOZZLE / ACCESSORIES (FIG. I–K)
•
Figure I - A crevice tool ( 4 ) is built into the nozzle and
can be extended as shown in Figure I by pulling the
extension piece until it locks into position.
•
ATTACHING PET HEAD (FIG. J)
CAUTION: The unit needs to be switched off when the
pet head is attached or detached.
NOTE: Do not use directly on pets.
Slide the dust bowl opening ( 3 ) into the opening of the
motorized pet head ( 8 ), ensuring that the connectors
( 12 ) engage with the recesses ( 13 ). An audible click will
be heard.
REMOVING PET HEAD (FIG. K)
CAUTION:
The unit needs to be switched off when the
pet head is attached or detached.
Pull the motorized pet head release tabs ( 12 ) outward.
•
Pull the main unit from the pet head ( 8 ).
SCENTED FILTER
BEFORE FIRST USE - remove bag from the scented
pre-filter. Reassemble per instructions above. When the
vacuum is turned on, the plastic scented filter will emit an
aroma to freshen the air.
ADVERTENCIA:
•
Causes mild skin irritation
•
Toxic to aquatic life
•
Harmful to aquatic life with long lasting effects.
•
Dispose of contents/ containers to an approved waste
disposal plant.
NOTE: When the plastic scented filter no longer lets off
the aroma, it can be an indication that the filter needs to be
replaced. See below for information on replacement filters.
*HHVJ325 vacuums are supplied with a scented filter,
though any vacuum covered in this manual can accept a
scented filter.
REPLACING THE FILTERS
The filters should be replaced every 6 to 9 months and
whenever worn or damaged. Replacement filters are
available from your Black+Decker dealer.
Catalog numbers:
•
Scented plastic pre-filter: VSPF10XX*
•
Cloth filter: VBF10
* XX is a placeholder for the two-digit number that indicates
the plastic scented filter's specific scent.
MAINTENANCE
Bowls and filters can be washed thoroughly; however, use
only mild soap and a damp cloth to clean the main part of
the vacuum. Important! To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment (other
than those listed in this manual) should be performed
by authorized service centers or other qualified service
personnel, always using identical replacement parts.
DETECCIÓN DE PROBLEMAS
If the product does not work, follow the instructions below.
If this does not solve the problem, please contact your local
BLACK+DECKER repair agent.
Unit will not start. Battery not charged
•
Check battery charging requirements.
Battery will not charge. Charger not plugged in
•
Plug charger into a working outlet. Refer to "Important
Charging Notes" for more details.
•
Check current at receptacle by plugging in a lamp or
other appliance.
Check to see if eceptacle is connected to a light switch
Publicidad
Tabla de contenido
