Functional Description - Black+Decker HLVA325J10 Manual De Instrucciones

WARNING: Do not attempt to modify or repair the
appliance
SAVE THESE INSTRUCTIONS
Symbols
• The label on your tool may include the following
symbols. The symbols and their definitions are as
follows:
V .......................volts
A .......................amperes
Hz.....................hertz
W......................watts
min ...................minutes
or AC ..........alternating current
or DC ......direct current
n o .....................no load speed
....................Class I Construction
(grounded)
.....................earthing terminal
...................safety alert symbol
....................Class II Construction
(double insulated)
.../min or rpm...revolutions or reciprocation
per minute

FUNCTIONAL DESCRIPTION

1. On/off switch
2. Dust bowl release button
3. Dust bowl
4. Extendable crevice tool
5. Filter
6. Charging terminals
7. Base charger
8. Pet head
9. Charger
10. Jack plug
11. Charging socket
CHARGING THE BATTERY (HLVA325JP)
WARNING: For use only with the supplied charger.
From new, the rechargeable cells of the product need a
minimum charge time of 16 hours to ensure full power.
• The switch must be in the off ("O") position, the product
will not charge if it is in any other position.
• Figure B - Plug the jack plug ( 10 ) of the charger into
the charging socket ( 11 ) of the tool. Plug the charger
into any standard 120 Volt 60 Hz electrical outlet or 220
Volts 50 Hz for the 220V models.
• While charging, the charger may get warm, this is
perfectly normal and safe. It is safe to leave the
appliance connected to the charger indefinitely. The
charger automatically reduces power consumption
when charging is complete.
WARNING: Do not charge the battery at ambient
temperatures below 39°F (4°C) or above 104°F (40°C).
CHARGING THE BATTERY (HLVA325BP)
WARNING: For use only with the supplied charger.
Before first use, the battery must be charged for at least
6 hours.
Place the appliance on the charging base ( 7 ) whenever it
is not in use as shown in Figure C.
Plug the charger into any standard 120 Volt 60 Hz or 220
Volts 50 Hz for the 220V models electrical outlet.
WARNING: Before charging, be sure to empty all
contents and dry thoroughly if needed to avoid damage
to your appliance.
Make sure the appliance is switched off. The battery will
not be charged when the on/off switch ( 1 ) is in the on
position.
NOTE: While charging, the charger may become warm.
This is normal and does not indicate a problem. The
appliance can be left connected to the charger indefinitely.
NOTE: Remove the pet head before charging.
WARNING: Do not charge the battery at ambient
temperatures below 39°F (4°C) or above 104°F (40°C).
SWITCHING ON AND OFF - FIGURE D
• Figure D - To start, slide the On/Off switch ( 1 )
forward (i.e. "O"= Off, "I" = On).
• To stop, slide the switch back.
• Return the product to the charger immediately after
use so that it will be ready and fully charged for the
next use. Ensure that the product is fully engaged with
the charger plug
CLEANING AND EMPTYING THE PRODUCT
WARNING: Projectile/Respiratory Hazard: Never use
the vac without its filter.
NOTE: The filter is re-usable, do not confuse it with a
disposable dust bag, and do not throw it away when the
product is emptied. We recommend that you replace the
filter every 6–9 months depending on frequency of use.
There are two methods of cleaning the bowl, a quick
empty method and a thorough clean method.
For a quick empty (Fig. E, F)
• Figure E - Press the dust bowl release button ( 2 ) on
the handle and remove the dust bowl.
• The top of the bowl is open when the bowl is removed
so that dust can be easy dumped without touching
the filter.
ENGLISH • 9