Jøtul GI 160 BF Instrucciones Para Instalación página 3

Kontroll av temperatur
Temperaturen styres
fjernbetjeningssystemet for en gitt tidsperiode, noe som igjen
justerer flammehøyden. Flammehøyden er avhengig av forhold
som rommets størrelse, temperatur, varmeeffekt, batteristyrke
etc. Fjernkontrollen måler hvor raskt romtemperaturen øker
når gassovnen er tent, og tilpasser tiden for neste
oppvarmingsperiode. Etter noen få oppvarmingsperioder, vil
styrken holde seg på et lavt nivå, dersom varmeeffekten er
tilstrekkelig til å opprettholde romtemperaturen. Dette gjør at
oppvarmingen varer lenger enn om gassovnen brukes på større
styrke.
Tilsyn
Hvis gassovnen blir etterlatt uten tilsyn i lengre tid, bør
fjernbetjeningssystemet skrus av eller til 'Pilot' posisjon. Vær
forsiktig når apparatet etterlates uten tilsyn – i sjeldne tilfeller
kan lydbølger fra andre kilder forårsake endringer i justeringen
av flammehøyden.
gjennom å aktivisere
ENGLISH
Fitting the optional remote
control system
Important: Make all the electrical connections before fitting
the batteries to the remote control system. Failure to do so
may cause damage to electrical components.
Fig. 1 Contents: A: Control valve, B: Microswitch,
C: Battery box, D: Bracket, E: Cables, F: Remote
control.
1. Remove the cover (fig. 2) from the control valve by removing
the screw (A) on the LH side and releasing the integral clip
on the RH side.
2. Mount the motor (fig. 3 A) onto the top LH side of the
control valve. Make sure that the bracket engages correctly
on the peg provided on the valve face and that the gears
mesh (fig. 3 B).
3. The new control cover can then be replaced with the cover
screw securing the motor bracket into position (fig. 2 A).
4. Attach the microswitch (the text facing upwards) on the
cover and fasten the screw (fig. 5). Take the four core wire
supplied. Thread the four small connectors over the gas
valve bracket and connect them to the motor and
microswitch. The two small connectors fit onto the
microswitch (fig. 5 B) (at the front LH side of the valve) - it
does not matter which way around these connections are
made. The medium and large connectors fit onto the motor
terminals (at the top LH side of the valve) (fig. 4 A-B) and
must be fitted to the correct sized terminals.
5. Make sure that the wires do not touch against the bottom
plate of the firebox as this can get hot and may damage the
wiring.
6. Fit the single multi-way connector to the terminals on the
electronic control box (fig. 6), making sure it is pushed firmly
home. The connector can only be fitted one way around.
7. Fit the batteries to the electronic control box (4 x AA size)
(fig. 7) and simply place the metal bracket to the hooks on
the back of the stove (fig. 9) (Not for Jøtul GI 160 BF). Make
sure all of the wiring is tidy and does not touch hot parts of
the stove such as the bottom plate of the firebox.
8. Fit the battery to the handset and follow the instructions
for setting up the remote control system.
Instructions for the optional remote
control system
Setting up the remote handset:
Display the desired format for temperature and
time.
Connect the battery or press 'Auto' and 'Timer' buttons together
- the display flashes, you are in 'SET' mode. Press 'Auto' to switch
from ºF to ºC as required. The display will automatically return
to manual mode after some time but pressing 'Timer' will return
to manual immediately.
Display the current time.
Connect the battery or press 'Auto' and 'Timer' buttons together
- the display flashes, you are in 'SET' mode. Press
hour or to set the minute. Wait or press 'Timer' to return to
manual mode.
to set the
3