Product Features; Technical Data; Noise/Vibration Information - Bosch GBM 10 RE Professional Manual Original

Intended Use
The power tool is suitable for drilling in wood, metal, ceramic
and plastic. Power tools with electronic control and clock-
wise/anti-clockwise rotation are also suitable for screwdriv-
ing and thread cutting.

Product Features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Keyless chuck
(2) Front sleeve
(3) Rear sleeve
(4) Belt clip
(5) Lock-on button for on/off switch
(6) On/off switch
Rotational direction switch
(7)
(8) Handle (insulated gripping surface)
a)
(9) Screwdriver bit
a)
(10) Universal bit holder
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical Data

Rotary Drill
Article number
Rated power input
Max. power output
No-load speed
Rated speed
Rated torque
Spindle collar diameter
Speed control
Clockwise/anti-clockwise ro-
tation
Max. drilling diameter
– Steel
– Wood
– Aluminium
Chuck capacity
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.

Noise/vibration information

Noise emission values determined according to
EN 62841-2-1.
Bosch Power Tools
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 83 dB(A); sound power level
94 dB(A). Uncertainty K = 5 dB.
Wear hearing protection!
Vibration total values a
determined according to EN 62841-2-1:
Drilling in metal: a
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
GBM 10 RE power tool and application tools, keeping their hands warm,
and organising workflows correctly.
3 601 D73 6..
W 600
Assembly
W 360
u
-1
min 0–2 600
-1
min 1 676
Changing the tool
Nm 20
mm 43
u
●
●
Keyless chuck (see figure A)
Hold the rear sleeve (3) of the keyless chuck (1) firmly and
turn the front sleeve (2) in rotational direction ➊ until the
mm 10
tool can be inserted. Insert the tool.
mm 25
Hold the rear sleeve (3) of the keyless chuck (1) and firmly
mm 10
tighten the front sleeve (2) by hand in rotational direction ➋
until you hear a click. This will automatically lock the drill
mm 1–10
chuck.
kg 1.7
The lock will disengage again if you turn the front sleeve (2)
in the opposite direction to remove the tool.
/ II
Screwdriving tools (see figure B)
You should always use a universal bit holder (10) when using
screwdriver bits (9). Only use screwdriver bits that fit the
screw head.
(triax vector sum) and uncertainty K
h
2
= 4.5 m/s , K = 1.5 m/s
h
Pull the plug out of the socket before carrying out any
work on the power tool.
Wear protective gloves when changing tools. The drill
chuck may heat up significantly when it is used for long
periods.
1 609 92A 59H | (12.03.2021)
English | 11
2