Battery Replacement - Elko EP TER-9 Manual Del Usario

Deleting of all programs
Auto
16--sep-- 10
PRG
in starting menu (time is shown
on display) - press simultaneously
button and and display
PRG OK
announces a notice all
Reset
Auto
TER-9
Performed by shortly pressing the hidden RESET button with a blunt-pointed object (e.g. a pencil
or screw-driver with a diameter of at most 2 mm).
The type of device and software version will be displayed for 1 second, then the device will enter
default mode. This means that the language is set to EN, all data is zeroed (thermostat function,
time/date, user programs, device options function).
An example of TER-9 programming
Setting the TER-9 in the function: two dependent thermostats with temperature setting T1 = 10°C a T2 20 °C with hysteresis setting T1 = 2 °C a T2 = 1°C.
With automatic controlled temperature change on 18.11.2010 at 6:52 p.m. to the temperature T1= 15 °C.
Auto Prog Prog
function
ter
16--sep-- 10
PRG OK
Prog Prog Prog
channel hysteresi
°C
OK
OK
+ _
Prog Prog Prog
year month day
OK OK
+ _ + _ + _
Warning
Device is constructed for connection in 1-phase main alternating current voltage AC 230 V or
24 V AC/DC (based on type of device) and must be installed according to norms valid in the
state of application. Connection according to the details in this direction. Installation, con-
nection, setting and servicing should be installed by qualifi ed electrician staff only, who has
learnt these instruction and functions of the device. This device contains protection against
overvoltage peaks and disturbancies in supply. For correct function of the protection of this
device there must be suitable protections of higher degree (A, B, C) installed in front of them.
According to standards elimination of disturbancies must be ensured. Before installation the
main switch must be in position "OFF" and the device should be de-energized. Don´t install
Prog
all
+
OK
OK
press button to complete
OK
the deleting of all set programs
TER-9
TER-9
Prog Prog
set function temperatur
+ _
OK OK
+ _
Prog Prog
channel hysteresi
°C
OK
OK
OK
+ _ + _
Prog Prog
hour minute
OK OK OK
+ _ + _

Battery replacement

You can change the battery without disassembling the device.
Auto
CAUTION
- only change the battery when the device is disconnected from power supply !!!
- the date and time must be reset after changing the battery !!!
- remove the plug-in module with the battery
- replace the original battery
- enter a new battery so that its upper edge (+) lines up with the plug-in module
- slide the plug-in module in the device and pay attention to polarity (+ up) – for roughly 1 s,
the display will show the name and the software version
- you can connect the device to power supply
Prog Prog Prog
channel
°C
OK OK
+ _
Prog Prog Prog
ter time prog
+ _
ESC
Prog Auto
on Prog add
16--sep-- 10
+ _
ESC
Prog
°C
+ _
the device to sources of excessive electro-magnetic interference. By correct installation en-
sure ideal air circulation so in case of permanent operation and higher ambient temperature
the maximal operating temperature of the device is not exceeded. For installation and setting
use screw-driver cca 2 mm. The device is fully-electronic - installation should be carried out
according to this fact. Non-problematic function depends also on the way of transportation,
storing and handling. In case of any signs of destruction, deformation, non-function or missing
part, don´t install and claim at your seller it is possible to dismount the device after its lifetime,
recycle, or store in protective dump.
8 / 8
Prog Prog
temperatur channel
OK OK OK
+ _
+ _
Prog Prog
add prog channel
OK OK OK
+
CR2032
Prog Prog Prog
temperatur hysteresi
°C
+ _
OK OK
Prog Prog Prog
day prog year prog
+ _
OK
OK
- long press (>1s)
- short press (<1s)