Descargar Imprimir esta página

Peavey HiSys 6XT Instrucciones De Uso página 2

Publicidad

Idiomas disponibles

Idiomas disponibles

Full Range Operation
Thank you for choosing Peavey's HiSys 6XT mid/high loudspeaker enclosure as part of your sound reinforcement
system. We take great pride in the design and manufacture of our units and you can expect top performance and
reliability. Your HiSys 6XT has been rigorously tested before packing and despatch to your dealer. Your HiSys 6XT
has been rigorously tested before packing and despatch to your dealer. A built-in crossover is fitted to optimise
performance under variable conditions and the unit leaves the factory pre-patched for passive/full range mode. The
nominal impedance of the HiSys 6XT is 8ohms.
Bi-amp Operation
The practice of bi amplification allows full control over the performance of the HiSys 6XT. To change the enclosure
from passive to bi amp mode or vice versa, it is necessary to gain access to the internal crossover board. The correct
procedure is as follows:-
1.
Remove the four screws retaining the grille. Remove the grille. Remove the four M5 bolts retaining the 10"
Scorpion. Remove the speaker. The crossover board can be viewed through the opening and two large sockets
will be visible.
2.
The lower of these white sockets is for passive operation. The upper socket is for bi-amp operation.
3.
As the enclosure leaves the factory pre- patched for passive use, the plug will be inserted in the lower socket.
Simply pull out the plug and repatch it to the upper socket. The enclosure will now be in bi-amp mode.
N.B. The plug will be very tight in its socket. This is necessary to achieve a low loss connection.
Crossover Selection
When operating in bi-amp mode it is important to select the correct crossover frequency and EQ. For use with
Peavey's CS Series power amplifiers with crossover islands we recommend a PL-1200EQ.
For use with other electronic crossovers and configurations, consult your Authorised Peavey Dealer. NOTE! EQ is
required for the 22XT compression driver.
Operation
The HiSys 6XT will normally be required to be used with a subwoofer such as the Peavey HiSys 112XT unless
response below 100Hz is not required. The HiSys 6XT is simply connected to the hi output of the HiSys 112XT
(refer to HiSys 112XT operating guide). To operate the HiSys 6XT and the HiSys 112XT in a bi amp mode situation
leave the HiSys 6XT in passive mode and repatch the HiSys 112XT for bi amp mode. An electronic crossover or
module offering a crossover point between 100 and 250Hz will now be required, (e.g. Peavey's PL-100, PL-150 or
PL-250). Simply connect the low pass to the input of the HiSys 112XT using pins 1+ and 1-, and the hi pass to the
HiSys 6XT input using Neutrik pins 1+ and 1-. To run the system in tri amp mode crossover frequencies of between
100 and 250Hz and 1200Hz (with 22XT compression driver EQ) will be required. Connect the low pass to the input
of the HiSys 112XT using Neutrik pins 1+ and 1-. Connect the mid pass to the HiSys 6XT using pins 1+ and 1-.
Connect the high pass out to the HiSys 6XT using pins 2+ and 2-.
Speakon Cable Wiring
Your HiSys 6XT is fitted with two low loss parallel Neutrik input sockets, which must be wired to a regular twin
conductor cable of adequate gauge using a 4-pole Neutrik plug, Peavey part # 00712570 (not supplied). Either
socket may be used as the input.
IN CASE OF DIFFICULTY CONSULT YOUR AUTHORISED PEAVEY DEALER
DANGER! LOUDSPEAKER CABLES CAN CARRY HAZARDOUS VOLTAGES. TAKE CARE IN TERMINATING
YOUR CABLES. PEAVEY STRONGLY RECOMMEND THAT THE POWER AMPLIFIER IS SWITCHED OFF
WHILST CONNECTING OR DISCONNECTING EITHER END OF THE LOUDSPEAKER CABLE.
DANGER! THIS ENCLOSURE HAS NOT BEEN DESIGNED TO BE FLOWN IN ANY WAY. NEVER ATTEMPT TO
SUSPEND USING THE HANDLES OR BY ANY OTHER MEANS.
CAUTION ! THIS SPEAKER IS CAPABLE OF HIGH SOUND PRESSURE LEVELS. USE EXTREME CARE IN
SETTING MAXIMUM LOUDNESS.
Due to our policy of continuing development, features and specifications are subject to change without notice.
HiSys 6XT
Mid/High Enclosure
OPERATING INSTRUCTIONS
Neutrik is a registered Trademark of NEUTRIK A.G.

Publicidad

loading