How To Operate Your Friedrich Room Air Conditioner; To Start Unit; To Set Mode Of Operation; Moneysaver ® Feature - Friedrich X-Star XQ05 Manual De Instalación Y Funcionamiento

How to operate your Friedrich room air conditioner

To start unit

f I o y r u i a c r n o i t i d n o r e s i s n i l l a t d e
ready to go. The first time the unit is started, the compressor will delay for three
minutes. See Automatic Component Protection on the following page.
1
Touch the Power button once. The unit will automatically be in Cool
mode with the temperature set at 75°F (24°C) and the fan speed at
F1, the sleep setting.

To set mode of operation

When you rst turn the unit on, it will be in the Cool mode (light on), with
constant fan.
2 Touch the Mode button once to activate the MoneySaver
MoneySaver ® s i f a a e r u t
so that the fan does not run all the time. This saves energy and
m i r p v o s e e d u h m i d i a c o i t
r i a m o e v m e t n o t ( e r u t n r o t
more times).
In order to run the fan by itself, do the following:
3
Continuing from MoneySaver
once to activate the FAN ONLY feature (light on).
The FAN ONLY setting will circulate air in the room without the com-
pressor coming on.

To adjust temperature

4 Use the Mode button to select either the COOL or MoneySaver
function
5 COOLER – Touch the
6 WARMER – Touch the
7 Press both the and
temperature readout from Fahrenheit (°F) to Celsius (°C).
Repeat step 7 to switch from °C back to °F.

To adjust fan speed

8 Touch the Fan Speed button to see the current setting. Touch it again
to change speed. F1 is the lowest setting (SLEEP SETTING / LOW),
F2 is MEDIUM, and F3 is HIGH.

To activate Smart Fan

9
There is a fourth option, SF, when selecting the fan speed. This is
the SMART FAN function. SMART FAN DOES NOT OPERATE IN
CONJUCTION WITH THE FAN ONLY MODE.
Smart Fan will adjust the fan speed automatically to maintain the
desired comfort level. For example, if the outside doors in your home
are opened for an extended period of time, or more people enter a
room, Smart Fan may adjust to a higher fan speed to compensate
for the increased heat load. This keeps you from having to adjust the
fan speed on your own.
4
a d n p u l g g d e n i o t a r p p o r e e r e c t p
®
t e a h c t c y s e l h t f e n a t i w t h e h o c
. n O y r u o m y a p e r e f c r n o t s n a f t n a
o c s n a t t n a f , n o t c u t h e h Mode button two
®
mode (light on), touch the Mode button
button to lower the room air temperature.
button to raise the room air temperature.
u b o t t s n a t t e h a s m t e m i e o t w s
920-197-01
c a e l i , s i t
PM
Speed
(light on).
On/Off
m p e r s s r o
r o f m o e r
13
To set the hour clock
10 Touch the Set Hour button to see the current setting (clock light
comes on). The number that is displayed is the approximate time
(hour only). Use the
SURE TO SET A.M. AND P.M. ACCORDINGLY. (P.M. is indicated
by a red light in the upper left corner of the display).

To set the timer

®
NOTE: Set the HOUR CLOCK before attempting to set timer functions.
You can set the START and STOP times a minimum of one hour apart, and
a maximum of twenty-three hours apart.
11 After setting the time, press the Set Hour button once (Start light
comes on). Use the
c t i t h e h
unit will START.
12 After selecting the START time, press the Set Hour button once more
(Stop light comes on). Use the
that the unit will STOP. After selecting the stopping time, press the
Set Hour button once.
13 Press the Timer On/Off button (light turns on) to activate the timer
function. To deactivate this function, press the Timer On/Off button
once again (light turns off). Once the on and off times have been
selected, they will remain in memory and cycle daily until changed.
NOTE: If the unit is unplugged or the power is interrupted, the HOUR
must be reset or the Timer On/Off will not function when desired.

Automatic component protection

Your unit is equipped with Automatic Component Protection. To protect the
compressor of the unit, there is a three minute start delay if you turn the unit
off or if power is interrupted. The fan operation will not be affected. Also, if you
switch from Cool mode to Fan Only, and switch back to Cool mode, there
is a three minute delay before the compressor comes back on.

(XQ models)

8 9 2 3 4
Cool
Fan
®
Money Saver
Mode
Fan Only
Clock
Timer Set
Start Time
Hour
Stop Time
10 11 12
and buttons to change the settings. BE
and
buttons to select the time that the
and
Figure 3
1
Power
Temp/Hour
6
5
7
buttons to select the time