Other Features - Haier QPHR50 Manual Del Propietário

CONTROLS
Appearance may vary by model.
Controls
NOTE: When the bucket is full or removed, the controls cannot be set.
1. Power Pad
Press to turn the dehumidifier on and off.
NOTE: Turning off the power by pressing the Power button does
NOT disconnect the appliance from power supply.
Controls the fan speed.
Press to select either High, Medium, Low, or Smart Dry fan speed.
Set the fan control to High for maximum moisture removal. When
the humidity has been reduced and quiet operation is preferred,
set the fan control to Medium or Low. Smart Dry compares the set
humidity level with the actual humidity and adjusts the fan speed
automatically.
3. Display
Shows the set % humidity level while setting, then shows the
actual (+/– 5% accuracy) room % humidity level.
in Nonstop mode for continuous operation. To set the unit for
continuous operation, press the
indicator light is illuminated.
NOTE: If Nonstop is selected, the dehumidifier will operate
continuously at its maximum dehumidification settings if attached
to a hose to drain or until the bucket is full. For drier air, press the
pad and set to a lower percent value (%). For damper air, press
the pad and set to a higher percent value (%). When you first use
the dehumidifier, set the humidity control to 45% or 50%. Allow at
least 24 hours for the dehumidifier to achieve the humidity level.
If you still have damper air than desired, set the humidity level to a
lower setting or select Nonstop for maximum dehumidification.

Other Features

Alarm
If the bucket is full or missing, an alarm will sound for about 10
seconds to remind you to empty and replace the bucket.
Auto Shut Off
The Water Level Control Switch shuts off the dehumidifier when the
bucket is full, or when the bucket is removed and/or not replaced
in the proper position. An alarm will sound if the water level control
switch is not reset.
49-5000429 Rev. 4
Humidity %
pad until the "Nonstop"
5. Filter Timer
After 250 hours of operation, the Clean the Filter indicator light will
glow to remind you to clean the filter. Remove the filter and clean it.
Press and hold Filter button for 3 seconds to reset the filter
reminder. See the Care and Cleaning section.
6. Delay Off
While the dehumidifier is operating press the Delay button.
Press the / buttons to select the number of hours you want
the dehumidifier to continue to operate before turning Off.
NOTE: After displaying the time, the Display will revert to showing
the current humidity after 5 seconds have passed. Pressing the
Delay button will display the number of hours left on the delay.
Delay On
While the dehumidifier is off press the Delay button.
Press the / buttons to select the number of hours you want
the dehumidifier to remain off before turning On.
NOTE: The display will show the number of hours left until the
dehumidifier turns on.
To cancel the Delay:
Press the Delay button once, the hours remaining on the Delay will
appear on the display. Press the Delay button again and the Delay
will be cancelled.
7. Pump
Activates the internal pump function. Press for 3 seconds to
activate the internal pump for automatic removal of condensate.
The internal pump indicator light will remain illuminated after 3
seconds. Press to deactivate the pump. Before turning on the
pump, ensure the hose is connected.
8. Empty Indicator
The "Empty" indicator will blink when the bucket is ready to be
emptied, or when the bucket is removed and/or not replaced in the
proper position.
NOTE: The fan and compressor will stop running as soon as the
bucket is removed.
Auto Defrost
When frost builds up on the evaporator coils, the compressor will
cycle off and the fan will continue to run until the frost disappears.
Power Outage
In the case of a power outage or interruption, the unit will automatically
restart, in the settings last used, after the power is restored.
Hold 3 Sec
Requires Hose
5