Stanley GBCPRO Manual De Instruccion página 7

7. Press the rapid charge button or maintenance charge button to start the charging process. A beep will sound. The digital
display will flash few times and will show the output current that is charging the battery.
Notes:
If the digital display shows "F02", the connection to the battery terminals is bad. Follow the steps outlined in "Important Safety Instructions" at the
front of this manual to disconnect, clean battery terminals, then reconnect.
If the digital display shows "F06", the RED (POSITIVE) and BLACK (NEGATIVE) clamps or O-rings are incorrectly connected to battery terminals. The
unit will sound a continuous alarm until the clamps or O-rings are disconnected. Follow the steps outlined in "Important Safety Instructions" at the
front of this manual to disconnect, then reconnect in correct polarity.
The unit will automatically adjust the output current.
If the battery is already charged to nearly full capacity, the unit' s output current may be reduced by a few amperes, despite the unit rating.
Once the unit is in rapid charge mode, maintenance charging mode can be alternatively selected by pressing the maintenance
charge button. Refer to the section of "Battery Maintenance Charging" section for further information.
8. When the charging is complete, the 3-character digital display will display "FUL".
Once "FUL" is displayed the charger may switch to another voltage, for instance from 6 to 12 volts or 36 to 48 volts, and charge
at 2 amps for a short period, then return to the correct battery voltage and display "FUL" again. This is normal, as the unit' s
microprocessor ensures the battery voltage detection was accurate.
IMPORTANT: Once the battery is fully charged, the unit will NOT automatically shut off. The unit will continue monitoring
the battery voltage. When the battery voltage drops below a predetermined value, the charger will automatically go into float
charging mode and the float charge indicator will light. This feature is ideal for maintaining a fully charged battery over long
periods non-use.
Note:
If there is any loss of power to the unit during the charging process, the unit will automatically return to the default settings when power is restored.
The battery type would be "GEL. " You must stop the charging process and use the battery type selector button to re-select the battery type if you are
charging a wet or AGM battery.
9. To end the charging function: If you pressed the rapid charge button to initiate the charging process, then press the rapid
charge button again to stop charging. Alternately, if you pressed the maintenance charge button to initiate the charging
process, then press the maintenance button again to stop charging. A beep will sound. The 3-character digital display will
show "000" to indicate the charger is back in standby mode.
10. To turn the unit OFF, follow the steps for disconnecting the unit outlined in "Important Safety Instructions" at the front of this
manual to disconnect.
Charging the Battery with the round Cart Connector or rectangular Cart Connector
WARNING: Make sure the round connector or rectangular connector are fully engaged (securely connected) before
charging. Attempting to charge when connectors are not fully engaged may cause property damage or injury.
IMPORTANT: The O-Ring connectors are universal to all golf carts. Some carts that use the Round and Rectangular Simple
connectors have an on-board computer that can inhibit charging. The O-Ring connectors are recommended in this instance. Refer to
the vehicle owner' s manual.
1. Insert either the Round Cart Connector or Rectangular Cart Connector into the unit' s charger connector.
2. Then plug the unit' s 120 volts power plug into a functioning AC outlet. The digital display will show the following red
circulating pattern that loops clockwise to indicate the charger is properly plugged in:
3. Connect the other end of either the Round Cart Connector or Rectangular Cart Connector into the golf cart' s charging port.
Make sure there is good contact.
4. When the charger is properly connected to the battery, the unit will automatically detect the battery voltage (6V, 12V, 24V, 32V
or 48V) and the appropriate battery voltage indicator LED will light. The 3-character digital display will show "000" to indicate
the charger is in standby mode (described at the end of this section) and is ready to use.
Note
: The unit may take several seconds to detect the battery voltage and during this period, pressing any buttons will have no effect.
"000" displays before proceeding to the next step.
5. Press the battery type selector button until the desired battery type LED lights. A beep will sound for each press of the button.
Notes:
The default selection is "GEL" type battery. Selecting an incorrect battery type may adversely affect charging performance. Refer to the battery
manufacturer' s specifications for battery type.
Ful
000
12
Make this selection BEFORE proceeding to the next step, as battery type cannot be selected once
charging has begun.
6. Press the rapid charge button or maintenance charge button to start the charging process. A beep will sound. The digital
display will flash few times and will show the output current that is charging the battery.
Notes:
If the digital display shows "F02", the connection to the battery terminals is bad. Follow the steps outlined in "Important Safety Instructions" at the
front of this manual to disconnect, clean battery terminals, then reconnect.
If the digital display shows "F06", the RED (POSITIVE) and BLACK (NEGATIVE) clamps or O-rings are incorrectly connected to battery terminals. The
unit will sound a continuous alarm until the clamps or O-rings are disconnected. Follow the steps outlined in "Important Safety Instructions" at the
front of this manual to disconnect, then reconnect in correct polarity.
The unit will automatically adjust the output current.
If the battery is already charged to nearly full capacity, the unit' s output current may be reduced by a few amperes, despite the unit rating.
Once the unit is in rapid charge mode, maintenance charging mode can be alternatively selected by pressing the maintenance
charge button. Refer to the section of "Battery Maintenance Charging" section for further information.
7. When the charging is complete, the 3-character digital display will display "FUL".
Once "FUL" is displayed the charger may switch to another voltage, for instance from 6 to 12 volts or 36 to 48 volts, and charge
at 2 amps for a short period, then return to the correct battery voltage and display "FUL" again. This is normal, as the unit' s
microprocessor ensures the battery voltage detection was accurate.
IMPORTANT: Once the battery is fully charged, the unit will NOT automatically shut off. The unit will continue monitoring
the battery voltage. When the battery voltage drops below a predetermined value, the charger will automatically go into float
charging mode and the float charge indicator will light. This feature is ideal for maintaining a fully charged battery over long
periods non-use.
Note:
If there is any loss of power to the unit during the charging process, the unit will automatically return to the default settings when power is restored.
The battery type would be "GEL. " You must stop the charging process and use the battery type selector button to re-select the battery type if you are
charging a wet or AGM battery.
8. To end the charging function: If you pressed the rapid charge button to initiate the charging process, then press the rapid
charge button again to stop charging. Alternately, if you pressed the maintenance charge button to initiate the charging
process, then press the maintenance button again to stop charging. A beep will sound. The 3-character digital display will
show "000" to indicate the charger is back in standby mode.
9. To turn the unit OFF, follow the steps for disconnecting the unit outlined in "Important Safety Instructions" at the front of this
manual to disconnect.
IMPORTANT: When disconnecting charger, first disconnect AC cord, then unplug the Round Cart Connector or Rectangular Cart
Connector from the golf cart' s charging port.
Checking the Battery Voltage
1. Set up the battery charger and connect to the battery following steps 1 through 5 in either the "Charging the Battery with
O-ring or Battery Clamps" or the "Charging the Battery with the Round Cart Connector or Rectangular Cart Connector" section.
When the unit is in standby mode:
2. Press the battery voltage button. A beep will sound and the show battery voltage LED will light. The digital display shows the
current voltage of the connected battery.
3. Press the battery voltage button again to end the process. A beep will sound and the show battery voltage LED will turn off.
The digital display will show "000".
When the unit is in maintenance charging or rapid charging mode:
2. Press the battery voltage button. A beep will sound and the show battery voltage LED will light. The digital display shows the
current voltage of the connected battery.
3. Press the battery voltage button again to end the process. A beep will sound and the show battery voltage LED will turn off.
The digital display will show the output current.
4. To turn the unit OFF, follow the steps for disconnecting the unit outlined in "Important Safety Instructions" at the front of this
manual to disconnect.
Battery Maintenance Charging
1. Set up the battery charger and connect to the battery following steps 1 through 5 in either the "Charging the Battery with
O-ring or Battery Clamps" or the "Charging the Battery with the Round Cart Connector or Rectangular Cart Connector" section.
2. Press the maintenance charge button. A beep will sound. The 3-character digital display will flash few times and then show
the output current that is charging the battery. In this mode, the output current is 2 amps.
Wait until the
3. To end the charging function, press the maintenance charge button again. A beep will sound. The 3-character digital display
will show "000" to indicate the charger is back in standby mode.
4. To turn the unit OFF, follow the steps for disconnecting the unit outlined in "Important Safety Instructions" at the front of this
manual to disconnect.
Ful
13