Product Description And Specifications; Technical Data - Bosch Professional GAS 25 L SFC Manual Original

OBJ_BUCH-464-008.book Page 12 Monday, December 12, 2016 2:10 PM
12 | English
Symbols and their meaning
Fold up the vacuum lid 3 and hold it. Grasp
the folded filter 12 by the fins, pull up and
remove.
Product Description and Specifica-
tions
While reading the operating instructions, unfold the graphics
page for the vacuum cleaner and leave it open.
Intended Use
The vacuum cleaner is intended for vacuuming and extraction
of materials that are not hazardous to one's health and for
non-flammable liquids. It is suitable for the increased de-
mands of industrial usage, as required in trades, industry and
workshops.
According to IEC/EN 60335-2-69, vacuum cleaners of dust
category L may only be used for vacuuming and extraction of
hazardous dusts with an exposition limit value > 1 mg/m
Use the vacuum cleaner only when you fully understand and
can perform all functions without limitation, or have received
appropriate instructions.
Product Features
The numbering of the product features refers to the illustra-
tion of the vacuum cleaner on the graphics page.
1 Cable holder
2 Carrying handle
3 Vacuum lid
4 Mode selector switch
5 Socket for power tool
6 Lock
7 Hose connection piece
8 Vacuum hose
9 Container
10 Latch of the vacuum cover
11 Dust bag
12 Folded filter
13 Motor protection filter
14 Level sensors
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.

Technical Data

All-Purpose Vacuum Cleaner
Article number
Rated power input
Frequency
Container volume (gross)
Net volume
The values given are valid for nominal voltages [U] of 230 V. For lower
voltage and models for specific countries, these values can vary.
1 609 92A 2N2 | (12.12.16)
All-Purpose Vacuum Cleaner
Dust bag contents
Vacuum (turbine), max.
Airflow (turbine), max.
Surface of folded filter
Weight according to EPTA-
Procedure 01:2014
Protection class
Degree of protection
The values given are valid for nominal voltages [U] of 230 V. For lower
voltage and models for specific countries, these values can vary.
Noise Information
Sound emission values determined according to
EN 60335-2-69.
Typically the A-weighted sound pressure level of the product
is less than 70 dB(A). Uncertainty K = 3 dB.
The noise level when working can exceed 80 dB(A).
3
.
Wear hearing protection!
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60335-1, EN 60335-2-69, EN
50581 .
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ECS,
70538 Stuttgart, GERMANY
Henk Becker
Executive Vice President
Engineering
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
 Before any work on the vacuum cleaner itself, pull the
mains plug.
Replacing/Inserting the Dust Bag (see figure A)
– Unlock the latches 10 and remove the vacuum lid 3.
– Pull off the full dust bag 11 from the connection flange to-
GAS 25 L SFC
ward the rear. Close the opening of the dust bag by folding
0 601 979 1..
down the lid. Remove the closed dust bag from the vacuum
cleaner.
W 1200
– Slide the new dust bag 11 over the connection flange of the
Hz 50/60
vacuum cleaner. Make sure that the full length of the dust
l 25
bag 11 faces against the inner wall of the container 9. Re-
l 16
attach the vacuum lid 3.
– Lock the latches 10.
GAS 25 L SFC
l 9
hPa 248
3
m /h 220
2
cm 4300
kg 11.8
/I
IP 24
Helmut Heinzelmann
Head of Product Certification
PT/ECS
Bosch Power Tools