General Safety Warnings And Precautions; Knowledge Of The Product And Preparation For Installation - moovo KSM001 Instrucciones Y Advertencias Para La Instalación Y El Uso

The design and manufacture of the devices making up the
product and the information in this manual fully comply with
current standards governing safety. However, incorrect
installation or programming may cause serious physical
injury to those working on or using the system. For this rea-
son, during installation, always strictly observe all instruc-
tions in this manual.
If in any doubt regarding installation, do not proceed and contact
the Moovo Technical Assistance for clarifications.
WORKING IN SAFETY!
Warning – for personal safety it is important to observe
these instructions.
Warning – Important safety instructions:
Keep these instructions in a safe place.
Observe the following warnings:
– make electrical connections exclusively as envisaged in
this manual incorrect: connections could cause serious
damage to the system.
– the power cable supplied must be suitable for indoor use,
and therefore must be protected by means of a tube embed-
ded in the wall or an external duct.
– never touch metal parts of the sockets on the battery cas-
ing with metal objects.

KNOWLEDGE OF THE PRODUCT AND PREPARATION FOR INSTALLATION

CHAPTER 1 – DESCRIPTION AND INTENDED USE
KSM001 is a system for solar power designed for Moovo auto -
mations for gates and garage doors (fig. 1).
Any other use is to be considered improper! The manufac-
turer declines all liability for damage resulting from improper
use of the product and other than as specified in this manual.
This system exploits exclusively sunlight to power an automa-
tion, without use of the electrical mains.
It can supply electrical energy continuously and permanently and
can be used anywhere (for example to automate a gate situated
far from the electrical mains).
The system comprises a photovoltaic panel (mod. MSP) and an
electric battery (mod. MBB):
– the photovoltaic panel is a device able to convert sunlight
directly into electrical energy.
– the battery is a device that stores the electrical power pro-
duced by the photovoltaic panel during the hours of sunlight,
making it available at any time of the day, including days with bad
weather. This device is equipped with a carry handle, a led indi-
cating operating status and two plugs for connection of the pho-
tovoltaic panel and the automation to be powered. The rear of
the battery is also fitted with 4 holes for wall-mounting.
CHAPTER 2 – COMPONENTS TO SET UP A COMPLETE
POWER SUPPLY SYSTEM
Fig. 2 illustrates all components used to set up a complete pow-
er supply system. The components are:
a) Photovoltaic panel mod. MSP;

GENERAL SAFETY WARNINGS AND PRECAUTIONS

Considering the risk situations that may arise during installa-
tion phases and use of the product, the devices supplied in
the pack must be installed in observance of the following
warnings:
– never make any modifications to part of the devices other than
those specified in this manual. Operations other than as speci-
fied can cause malfunctions. The manufacturer declines all liabil-
ity for damage caused by makeshift modifications to the product.
– never place devices near to sources of heat and never expose
to naked flames. This may damage system components and
cause malfunctions, fire or hazardous situations.
– ensure that the devices cannot come into contact with water or
other liquids. During installation ensure that no liquids penetrate
the devices present.
– the product packaging material must be disposed of in full
observance of current local legislation governing waste disposal.
Warning! – Keep this manual in a safe place to enable future
product maintenance and disposal procedures.
b) Bracket for fixture of the photovoltaic panel;
c) Metal hardware (screws, washers, etc.);
d) Electric battery (mod. MBB);
e) Power cable for connection between the battery and auto -
mation;
f) "L" type sockets;
g) Screws for "L" type socket fixture.
• Optional Accessories (not supplied in pack)
KSM001 enables complete power autonomy of the system only
if used in full compliance with the conditions specified in Chapter
3. If these limits are exceeded – for example due to intense use
of the automation exceeding the maximum recommended num-
ber of manoeuvre cycles – the power stored by the battery may
be reduced.
For this type of problem, a power supply unit is available (mod.
MBC – optional accessory) for temporary connection to the elec-
trical mains. This enables the user to restore full battery charge
status in just a brief time.
CHAPTER 3 – PRELIMINARY INSTALLATION CHECKS
AND PRODUCT APPLICATION LIMITS
To ascertain suitability of the product with respect to the specific
features of the automation to be powered, the following checks
should be performed as well as a check for compliance of the
technical data in the chapter "Product technical specifications".
In the vicinity of the automation to be powered, locate the ideal
point for installation of the photovoltaic panel and the location for
English – 1