Initial Start-Up - Intimus 007SL Instrucciones De Uso

GB
APPLICATION:
The document shredder INTIMUS 007SL / 007SF /
007SE is a machine for the destruction of common
written material.
The machine may only be used to
shred paper!
Shredding of other types of data carriers
and of staples and paper clips may lead
to injuries (for example due to splintering
of hard materials etc.) and damage to
the machine (for example destruction of
the cutter etc.).
OPERATING FUNCTIONS:
1 = Rocker switch „ready" (fig. 1)
Depress this switch to start the machine or
to stop the machine.
2 = „Cutting system forward"
pushbutton (fig. 2)
Pressing this button starts the cutting system.
Material can now be fed to the shredder.
3 = „Cutting system stop"
pushbutton (fig. 2)
Pressing this button switches the shredder
off, thereby halting the cutting system.
4 = „Cutting system reverse"
pushbutton (fig. 2)
Pressing this button starts the cutting system
in reverse.
5 = Pilot lamp „ready" (fig. 2)
Lights when the rocker switch (1) is opera-
ted.
6 = Pilot lamp „receptacle full" (fig. 2)
Lights as soon as the receptacle is full and
needs to be emptied. At the same time the
machine switches off automatically.
7 = Pilot lamp „door open" (fig. 1)
Lights when the door is not closed. The
machine then switches off automatically and
it cannot be started as long as the door is
open.
8 = Light barrier (forward operation) (fig. 3)
The shredding operation is started as soon
as a sheet of paper passes through the feed
slot.
1
fig. 1
INITIAL START UP
INSTALLATION:
- Unpack and set machine upright.
- Place plastic or paper sack into the receptac-
le.
- Plug in the machine (for instructions for the
necessary precautions see „TECHNICAL
DATA".
OPERATION
OPERATING THE MACHINE:
To start, switch on the unit by operating the rocker
switch (1) (fig. 1).
The pilot lamp marked „ready for operation" (5),
as well as the red stop-button „S" (3) (fig. 2) will
light to indicate that the machine is ready for
operation.
The paper tray may not be used as
a step ladder or as a seat. Danger of
tipping over!
FEEDING PAPER:
- Feed paper through the inlet guide to the cutting
system.
- Machine switches automatically to forward and
draws paper in.
- The machine switches off automatically after
shredding.
Note: In order to always obtain a correct cutting
result in terms of particle size and thus achieve
the safety class according to DIN 32757 as
stated in the brochure, the material to be cut
must always be fed into the cutting mechanism
at a right angle to the cutting mechanism and in
appropriate quantities in the middle of the inlet
slot.
S
4 3 2 5
fig. 2
8
fig. 3
4
The air vents in the housing are ne-
cessary for cooling and may not be
covered or closed!
The mains connection at the machine
must be freely accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 25°C!
Never feed the shredder with a quantity
of paper exceeding the maximum indi-
cated in the technical details.
Should the machine be overfed, follow
the instructions under „AUTOMATIC
RESPONSE IN CASE OF OVERLOA-
DING".
EMPTYING THE RECEPTACLE (Fig. 4):
When the receptacle is full, the machine turns
off automatically and a horn sounds. The pilot
lamp (6) (fig. 2) lights up. Empty the receptacle
as follows:
- Open door. The pilot lamp (7) (fig. 2) lights
up.
- Pull the receptacle out of the machine.
- The horn stops. The pilot lamp (6) goes off.
- Remove the full sack and dispose of con-
tents.
- PLace empty sack into receptacle, push in the
receptacle and close door. The pilot lamp (7)
goes off.
Note: The machine will only run with closed
door!
6 7
007SL/SF
007SE
fig. 4