Important Warning - Chicco NIGHTLIGHT Manual De Instrucciones

Ocultar thumbs Ver también para NIGHTLIGHT:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 14
Nightlight
I
GB

IMPORTANT WARNING

WARNING: The opening between the side of the door and
the outer-most vertical members of the barrier shall be less
than 65 mm
IMPORTANT: Please read these instructions carefully befo-
re use and keep them for future reference. For your child's
safety, read these instructions carefully.
WARNING: Before use, remove and dispose of all plastic
bags and packaging materials and keep them out of reach
of newborn babies and children.
WARNINGS
• This guard is approved to European regulation EN
1930:2000 (and subsequent amendment A1:2005)
when it is fitted in accordance with the instructions.
• WARNING: The incorrect fitting or positioning of this
safety barrier can be dangerous.
• WARNING: This safety barrier must not be fitted across
windows.
• Only use this product as a staircase guard or door guard
indoors.
• This guard has been designed for children up to 24 mon-
ths of age.
• WARNING: Children over 24 months of age could climb
on the guard and pose a risk of danger to their safety.
• WARNING: Stop using the safety barrier if the child is
capable of climbing it.
• WARNING: Periodically check that the guard is fitted
and fixed correctly.
• Check that the surfaces where you wish to fit the guard
are suitable for this purpose and that they are structural-
ly solid.
• WARNING: Do not use the safety barrier if any of its par-
ts are damaged or missing.
• WARNING: Only use spare parts supplied or approved
by Artsana S.p.A..
MAINTENANCE
Periodically check the condition of the anchoring surfaces,
cranks, shafts, wall caps and the correct operation of the
locking device of the safety guard.
The cleaning and maintenance of this product must be
carried out on a regular basis by the user.
The cleaning and maintenance must only be carried out
by an adult.
• Clean the plastic parts with a soft damp cloth.
• If the highchair comes into contact with water, dry the
metal parts to prevent the formation of rust.
PACK CONTENT (DIAGRAM A)
1. Safety guard
2. Shaft (x 4)
3. Crank (x 4)
4. Wall cap (x 4)
5. Adhesive strips (x 4)
6. Screw (x 4)
7. Spacer for fitting the guard.
HOW TO ASSEMBLE THE PRODUCT
Screw the cranks to the end of the shafts, taking care to fit
them in the correct positions, as shown in diagram B.
Insert each shaft, with the crank correctly tightened into
position, into each of the appropriate housings located on
the corners of the guard (diagram B).
CERAMIC TILED SURFACE
PLASTIC SURFACE
(eg. UPVC DOOR FRAME)
METAL SURFACE
(eg. ALUMINIUM/STEEL DOOR
FRAME)
WALLPAPERED
SURFACE
PLASTER BOARD STUD WALL
- WOODEN SUPPORTING
BATTEN RECOMMENDED
PLASTERED
SURFACE
UNSUPPORTED WOODEN
SURFACE
(eg. STAIR/NEWEL POST)
RIGIDLY SUPPORTED WOODEN
SURFACE
(eg. DOOR FRAME/SKIRTING
BOARD)
HOW TO POSITION THE SAFETY GUARD
Minimum width: 760 mm
Maximum width: 810 mm
The safety guard can be fitted with extensions to suit larger openings.
WARNING: Fitting the guard in the incorrect position can
be dangerous for your child's safety.
The guard must be fitted in such a way so that it opens in
the direction opposite to the staircase.
WARNING: If the safety guard is positioned at the top of
the stairs, it must not be fitted below the highest step. If
the safety guard is positioned at the bottom of the stairs,
it must be fitted in correspondence with the lowest step
(diagram C). Check that the surfaces on which the safety
guard is fitted are suitable and solid.
Note: Fitting the safety guard to certain surfaces may requi-
re purchasing appropriate fixing accessories (i.e.: inserts).
HOW TO FIT THE SAFETY GUARD
WARNING: To ensure the correct operation of the auto-clo-
se locking mechanism, the safety guard must be fitted in a
perpendicular position with respect to the floor's surface, as
shown in diagram D.
12

Publicidad

Tabla de contenido
loading

Tabla de contenido